manualshive.com logo in svg

John Bean 48109B, Инструкция по установке и эксплуатации

Поделиться
Скачать
John Bean 48109B Скачать руководство пользователя страница 16

16 of 40 

 

 

Figure 6 - Safety release rod location. 

 
3.

 

Install the rectangular safety release tab using one (1); 1/4” - 20UNC x 3/4”lg. cap screws.  
The safety release tab screws to the surface of the safety release rod located under the 
mechanical safety locks. 

 
4.

 

Using Figure 7

, 

attach the rod end to the air cylinder, and assemble it to the safety release plate 

using the shoulder bolt supplied in the hardware kit.  Connect the safety release plate to the 
safety release rod using two (2) hex bolt and lockwashers. 

 
5.

 

Assemble the breather and 90° elbow to the air cylinder as shown in Figure 7.  Attach the air 
cylinder to the baseframe using the shoulder bolt provided. 

 
6.

 

Install the safety release connecting rod between the safety bars using  ¼”-20UNC x  1¼” lg  
hex bolt, nut and lockwasher, using one on each side. 

 
7.

 

Place the safety bar weldments back in their engaged position. 

 Turn power back on.

 

 

Содержание 48109B









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды