jobmate JMCMS18G, Инструкция по безопасности и эксплуатации

Страница: 5 / 16

5
ill-suited models.
12. Ensure that the connection between the battery
charger and battery is correctly positioned and is
not obstructed by foreign bodies.
13. Keep battery charger’s slots free of foreign objects
and protect against dirt and humidity. Store in a dry
and frost-free place.
14. When charging batteries, ensure that the battery
charger is in a well-ventilated area and away from
inflammable materials. Batteries can get hot during
charging. Do not overcharge any batteries. Ensure
that batteries and chargers are not left unsupervised
during charging.
15. Do not recharge non-rechargeable batteries, as they
can overheat and break.
16. Longer life and better performance can be
obtained if the battery pack is charged when the
air temperature is between 18 ℃ and 24 ℃ . Do not
charge the battery pack in air temperatures below
4.5 ℃ , or above 40.5 ℃ . This is important as it can
prevent serious damage to the battery pack.
17. Charge only battery pack of the same model
provided by POSITEC and of models recommended
by POSITEC
SAFETY WARNINGS FOR
BATTERY PACK
a) Do not dismantle, open or shred cells or battery pack.
b) Do not short-circuit a battery pack. Do not store
battery packs haphazardly in a box or drawer where
they may short-circuit each other or be short-circuited
by conductive materials.
When battery pack is not
in use, keep it away from other metal objects, like
paper clips, coins, keys, nails, screws or other small
metal objects, that can make a connection from one
terminal to another. Shorting the battery terminals
together may cause burns or a fire.
c) Do not expose battery pack to heat or fire. Avoid storage
in direct sunlight.
d) Do not subject battery pack to mechanical shock.
e) In the event of battery leaking, do not allow the liquid
to come into contact with the skin or eyes. If contact
has been made, wash the affected area with copious
amounts of water and seek medical advice.
f) Seek medical advice immediately if a cell or battery pack
has been swallowed.
g) Keep battery pack clean and dry.
h) Wipe the battery pack terminals with a clean dry cloth if
they become dirty.
i) Battery pack needs to be charged before use. Always
refer to this instruction and use the correct charging
procedure.
j) Do not maintain battery pack on charge when not in use.
k) After extended periods of storage, it may be
necessary to charge and discharge the battery pack
several times to obtain maximum performance.
l) Battery pack gives its best performance when it is
operated at normal room temperature (20 °C ± 5 °C).
m) When disposing of battery packs, keep battery
packs of different electrochemical systems separate
from each other.
n) Recharge only with the charger specified by
manufacturer. Do not use any charger other
than that specifically provided for use with the
equipment.
A charger that is suitable for one
type of battery pack may create a risk of fire
when used with another battery pack.
o) Do not use any battery pack which is not designed
for use with the equipment.
p) Keep battery pack out of the reach of children.
q) Retain the original product literature for future
reference.
r) Remove the battery from the equipment when not in
use.
s) Dispose of properly.
GENERAL SAFETY WARNINGS
FOR YOUR LASER
WARNING:
Read all safety warnings and all
instructions.
Failure to follow the warnings
and instructions may result in serious injury.
Save all warnings and instructions for future reference.
These lasers do not normally present an optical
hazard although staring at the beam may cause
flash blindness.
Do not stare directly at the laser beam. A hazard
may exist if you deliberately stare into the beam,
please observe all safety rules as follows:
1. The laser shall be used and maintained
in accordance with the manufacturer’s
instructions.
2. Never aim the beam at any person or an
object other than the work piece.
3. The laser beam shall not be deliberately aimed
at another person and shall be prevented from
being directed towards the eye of a person for
longer than 0.25 seconds area.
4. Always ensure the laser beam is aimed at a
sturdy work piece without reflective surfaces,
e.g. wood or rough-coated surfaces are