jobmate JMCMS18G, Инструкция по безопасности и эксплуатации

Страница: 14 / 16

14
4) Rotate the table until the pointer is positioned at 0°.
5) Release mitre latch and tighten the mitre locks.
6) Loosen the bevel lock and set the saw arm at
0°bevel (the blade at 90°to the mitre table). Tighten
the bevel lock.
7) Place a set square against the table and the flat
part of the blade.
8) Rotate the blade by hand and check the blade-to-
table alignment at several points.
9) The edge of the set square and the saw blade
should be parallel.
10) If the saw blade angles away from the set square,
adjust as follows.
11) Use an 10 mm wrench or adjustable wrench to
loosen the lock nut securing the 0° bevel adjustment
screw. Also, loosen the bevel lock.
12) Adjust the 0° bevel adjustment screw using a 4
mm hex key to bring the saw blade into alignment
with the square.
13) Loosen the Phillips head screw holding the
pointer of the bevel scale and adjust the position of
the pointer so that it accurately indicates zero on the
scale. Retighten the screw.
14) Retighten the bevel lock and the lock nut securing
the 0° bevel adjustment screw.
7. SETTING THE FENCE SQUARE WITH THE TABLE
1) Make sure that the electrical plug is removed from
the power point.
2) Push the saw arm down to its lowest position and
engage the release knob to hold the saw arm in the
transport position.
3) Loosen the mitre locks and lifting up the mitre
latch.
4) Rotate the table until the pointer is positioned at
0°.
5) Release mitre latch and tighten the mitre locks.
6) Using a 5 mm hex key, loosen the two screws
securing the fence to the base.
7) Place a square against the fence and alongside
the blade.
8) Adjust the fence until it is square with the blade.
9). Tighten the screws securing the fence.
10) Loosen the Phillips head screw holding the
pointer of the mitre scale and adjust it so that it
accurately indicates the zero position on the mitre
scale.
11) Retighten the screw securing the mitre scale
pointer.
8. CHANGING A BLADE
1) Make sure that the battery pack is removed from
the machine.
2) Push down on the operating handle and pull the
release knob to release the saw arm.
3) Use the screwdriver to loosen the cover plate
screw
4) Pull the rotating blade guard up.Assure the lowest
point of the rotating blade guard is positioned over
the upper fixed blade safety guard, the blade bolt
cover should have been moved and now it is possible
to access the blade bolt.
5) Use your right hand to press the spindle lock
button. Use you left hand to rotate the blade until
the spindle locks.
6) Use the 6 mm hex key provided to loosen and
remove the blade bolt. (Loosen in a clockwise
direction as the blade screw has a left hand thread).
7) Remove the outer flange and the blade.
8) Fit the new blade onto the spindle, taking care that
the inner flange sits behind the blade.
9) Replace the outer flange.
10) Depress the spindle lock button and replace the
blade bolt.
11) Use the 6 mm hex key provided to tighten the
blade bolt securely (tighten in an anti-clockwise
direction).
12) Lower the blade guard, hold the rotating lower
blade guard and blade bolt cover in position and
tighten the fixing screw to secure the blade bolt
cover in position.
WARNING ! The blade bolt cover must be positioned
correctly and the bolt cover screw must be screwed
securely before you conduct the next move.
13) Check that the blade guard operates correctly
and covers the blade as the saw arm is lowered.
14) Connect the saw to the battery pack and run the
blade to make certain that it is operating correctly.
MAINTENANCE
WARNING: Remove the battery pack from
the tool before carrying out any adjustment,
servicing or maintenance.
There are no user serviceable parts in your power
tool. Never use water or chemical cleaners to clean
your power tool. Wipe clean with a dry cloth. Always
store your power tool in a dry place. Keep the motor
ventilation slots clean. Keep all working controls free
of dust. Occasionally you may see sparks through the
ventilation slots. This is normal and will not damage