co
tto
n/
lin
en
si
lk/
woo
l
sy
nthe
tics
MIN
co
tto
n/
lin
en
si
lk/w
ool synthetic
s
MIN
co
tto
n/
lin
en
si
lk/w
ool synthetic
s
MIN
co
tto
n/
lin
en
si
lk/w
ool synthetic
s
MIN
co
tto
n/
lin
en
si
lk/w
ool synthetic
s
MIN
7
8
Using Phoenix Gold
®
FreeFlight
for the first time
Before ironing your clothing or fabrics for the
first time, it is recommended that you use
Phoenix Gold
®
FreeFlight on a damp piece of
cloth for a few minutes. This will ensure that
any residue left over from the manufacturing
process is burnt off the Ceramic Plate and
won’t transfer to your clothes.
You may notice a slight odour and a small
amount of smoke during this time, but this
is perfectly normal and should disappear
quickly.
In hard water areas, we recommend a
mix of 50% tap water and 50% distilled or
‘demineralised’ water.
Only use clean, pure water that contains
no contaminants or additional chemicals.
Important -
Each iron is checked at the
factory so some water may remain in the tank.
Please flush the system by filling the
tank and setting the iron on the highest
temperature and press the steam trigger
to release steam.
Do this at least once before first use and
also if you haven’t used your Phoenix Gold
®
FreeFlight for a long period.
Basic instructions
1.
Lift the Water Tank Cap
(C)
and fill with
water. When filling the tank from empty,
hold nearly vertical and, using the jug
provided, fill to the ‘Max’ line on the
Phoenix Gold
®
FreeFlight. When topping
up, remove the iron clear of the base,
open the Water Tank Cap, and tilt the iron
upwards. Slowly fill below the ‘Max’ line,
and close the cap again.
Using Phoenix Gold
®
FreeFlight
Using Phoenix Gold
®
FreeFlight
continued
Note:
Some water can get trapped inside
the cap and come out of the small air hole
when the iron is held vertically. This is not a
leak, simply open the cap and empty out
any residual water.
Also, there can sometimes be a noise
created by air being vented through the air
hole in the cap. If this occurs, simply open
the cap to stop it happening.
2.
Plug Phoenix Gold
®
FreeFlight into the mains
and switch on. Make sure the steam is set
to off while the iron is heating (indicated by
the thermostat light on the iron).
When used with the cord the light will go
on and off as the temperature regulates.
When used cordless the iron should be
placed back on the base unit to maintain
heat. When the thermostat light is off
the iron is ready.
PLEASE MAKE SURE THE STEAM
SELECTOR IS CLOSED WHEN USING
THE STEAM TRIGGER IN QUICK
SUCCESSION TO AVOID WATER
SPITTING.
Do not open the selector
immediately after using the Steam Blast as
the pressure can cause water to come out
of the soleplate. Always check to make sure
the 'Auto-Off' feature has not activated when
using the Steam Blast as this can cause the
iron to cool quickly and water to spit from
the soleplate.
Anti-calc system
A special resin filter inside the water tank
prevents scale build-up in the plate. The
resin filter is permanent and does not need
replacing.
Do not use chemical additives, scented
substances or decalcifiers.
Anti-drip system
With the anti-drip system, you can iron even
the most delicate fabrics.
Always iron these fabrics at low temperatures.
The plate may cool down to the point where
no more steam comes out, but rather drops
of boiling water that can leave marks or stains.
Turn the steam selector to the off position so
the Anti-drip activates to prevent vaporization,
to help avoid the risk of staining.
Preparation
Sort the laundry to be ironed according to
the international symbols on the garment
label or, if this is missing, according to the
type of fabric.
Garment label
Fabric type
Thermostat regulation
Synthetic
Low temperature
Silk - Wool
Medium temperature
Cotton - Linen
High temperature
Fabric not to be ironed
Start ironing the garments requiring a low
temperature.
This reduces the waiting times (the iron takes
less time to heat up than to cool down) and
eliminates the risk of scorching the fabric.
Automatic shut-off
If the iron (connected to the base with
the power on) has been left idle for approx.
30 seconds in the
horizontal
position,
heating will shut-off. When this happens,
the automatic shut-off indicator light
(K)
will
blink. Lift the iron to the
vertical
position to
deactivate this safety feature and allow the
iron to heat before commencing with ironing
again.
If the iron (connected to the base with
the power on) is in use over 30 minutes
(approx) a safety feature will activate and the
heating will shut-off. When this happens,
the Automatic Shut-off Indicator Light
(K)
will blink. Lift the iron to the horizontal and
back to the vertical position to deactivate
this safety feature, (which will be indicated
by a constant blue light) and allow the iron
to heat to the required temperature before
commencing with ironing again.
Содержание Phoenix Gold FreeFlight
Страница 1: ......
