co
tto
n/
lin
en
si
lk/w
ool synthetic
s
MIN
co
tto
n/
lin
en
si
lk/w
ool synthetic
s
MIN
co
tto
n/
lin
en
si
lk/w
ool synthetic
s
MIN
co
tto
n/
lin
en
si
lk/w
ool synthetic
s
MIN
co
tto
n/
lin
en
si
lk/w
ool synthetic
s
MIN
co
tto
n/
lin
en
si
lk/w
ool synthetic
s
MIN
cotton/linen
silk
/w
oo
l
sy
nth
etic
s
M
IN
co
tto
n/
lin
en
si
lk/w
ool synthetic
s
MIN
9
10
the appropriate temperature for best
performance.
5.
When the Temperature Indicator Light
(H)
goes out, you can start to iron.
•
If the iron is connected to the base, you
can continue ironing.
•
If the iron is being used separately,
you can use for about 30 seconds
after the Temperature Indicator Light
(H)
goes out (this will vary depending
on various factors), then you need to
replace the iron on the base for heating,
you can continue to use again after the
Temperature Indicator Light
(H)
goes out.
6.
Set the Steam Selector
(D)
to a required
position.
[Fig. 1]
Using the Steam Blast Trigger (F)
and
steam when ironing vertically.
IMPORTANT: Place the steam selector
to the CLOSED position to maintain the
pressure for the steam blast function
and to avoid water spitting when the
steam trigger is pressed.
After the iron has fully heated press the
Steam Blast Trigger
(F)
to generate a
powerful burst of steam that can penetrate
fabrics and smooth difficult creases.
Wait for at least 2 seconds before pressing
again.
[Fig. 6]
By pressing the Steam Blast Trigger
(F)
at
intervals you can also iron vertically (curtains,
hung garments, etc.).
[Fig. 7]
Warning: the Steam Blast Trigger (F)
function can only be used at high
temperatures. Remember to replace the
iron on the base when using in cordless
mode. Once the temperature light has
gone out remove from the base and
continue to steam. Always read the care
label.
Steam Ironing
Filling the tank
1.
Check that the plug is disconnected from
the socket.
2.
Detach and move the iron clear of the
base before filling.
3.
Move the Steam Selector
(D)
to
[Fig. 1]
4.
Open the Water Tank Cap
(C)
.
5.
Raise the tip of the iron to help the water
enter the opening without overflowing.
6.
Slowly pour the water into the tank using
the jug (supplied) and take care not to go
over the maximum level (about 370ml)
indicated by “MAX” on the tank
(O).
[Fig.
2]
7.
Close the Water Tank Cap
(C)
.
Selecting the steam
1.
Use the higher temperature setting from
dot positon two to dot position three to
generate even steam flow and to avoid
the possibility of water spitting.
2.
Ensure there’s enough water in the water
tank, put the iron in the vertical position.
Wipe away any water that may be around
the cap.
3.
Select the required temperature on the
Temperature Control Dial
(G)
(must be
within the steam range as shown on the
dial).
[Fig. 3]
4.
Connect the iron to the base and insert
the plug into the socket:
•
When using the iron connected to its
base
[Fig. 4]
, make sure that the Base
Lock Switch
(L)
is in the locked position.
•
When using the iron separately from
the base
[Fig. 5]
, put the iron vertically
on the base, and wait for it to reach
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Using Phoenix Gold
®
FreeFlight
continued
Using Phoenix Gold
®
FreeFlight
continued
C
D
L
F
H
Содержание Phoenix Gold FreeFlight
Страница 1: ......
