JLG E450A Скачать руководство пользователя страница 63

Страница: 63 / 480

SECTION 3 - CHASSIS & TURNTABLE

3121714

3-23

Cover Assembly

NOTE:

Refer to Figure 3-17., Cover Assembly.

Grease O-Ring (6E) and insert into internal groove in
Cover (6A).

Assemble Disengage Cap (6B) onto Cover (6A) using two
Hex Head Bolts (6C). Torque bolts to 70-80 in-lbs.

Insert Disengage Rod (6D) into hole in Cover (6A) until it
touches the inside of the Disengage Cap (6B).

NOTE:

The Disengage Rod can be inserted either end first.

Grease Face of Thrust Washer (2) and place in Cover (6A)
making sure that tangs on washer seat into pockets in
cover.

Install O-Ring Pipe Plugs (6F) into Cover (6A). The plugs
should be hand tight according to SAE standard.

Main Assembly

NOTE:

Refer to Figure 3-11., Main Assembly - Sheet 1 of 2 and Fig-

ure 3-12., Main Assembly - Sheet 2 of 2.

NOTE:

All components should receive a generous amount of lubri-

cant oil as they are being assembled.

Place Hub-Spindle Sub-Assembly on the bench.

Grease O-Ring (18) and place it into groove of Hub (1G).

Place Ring Gear (1F) onto Hub (1G). Align the three ship-

ping capscrew holes on Hub (1G) and Ring Gear (1F).

Install three shipping Capscrews (19) into ring gear and

hub. Torque them to 15-20 ft-lbs.

Place Output Carrier Sub-Assembly (4) into mesh with

Spindle (1A) splines.

Place External Retaining Ring (5) over 13T spline to the

retaining groove on Input Shaft (9).

NOTE:

For ratio 48:1, assemble Output Sun Gear (11) over Input

Shaft (9) first, then install External Retaining Ring (5).

Using appropriate tool to install Retaining Ring (20) into

groove on Output Sun (11)

Place Input Shaft (9) spline end into mesh with Internal

Coupling (7) splines.

With the modified spline end facing up, place the Out-

put Sun Gear (11) into mesh with the output planet

gears.

10.

Place Input Carrier Sub-Assembly (3) onto Output Sun

Gear (11) splines. Drop Input Sun (10) into mesh with

planet gears for specific ratios, if required. (No timing

required).

11.

Grease O-Ring (17) and insert into groove in Cover Sub-

Assembly (6).

12.

Install Cover Sub-Assembly (6) into Ring Gear (1F)coun-

terbore and install Retaining Ring (6G) into groove in

Ring Gear (1F).

13.

Attach ID Tag (15) onto unit using Drive Screws (16).

14.

Check disconnect, roll and air check unit, leak check

brake, and record release pressure.

15.

Insert Plastic Plug (12) into place if applicable.

Содержание E450A

































































































































































































































































































































































































































































































Результаты поиска

Содержание E450A

Отзывы:

Бренды по названию

Популярные бренды

JLG E450A, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание E450A

Отзывы:

Бренды по названию

Популярные бренды