JLG E450A, Руководство по обслуживанию и ремонту

Страница: 387 / 480

SECTION 6 - JLG CONTROL SYSTEM
3121714 6-71
22 19 L/S JOY. OUT OF RANGE HIGH The PM detects that the Lift or Swing joystick sig-
nal voltage > 8.1V and reports the fault to the
UGM. The PM detects that the lift/swing center tap
voltage is between 3.31 and 3.75 volts and no
longer reports the fault to the UGM
22 20 L/S JOY. CENTER TAP BAD The PM detects that the Lift or Swing center tap
voltage is not between 3.31 volts and 3.75 volts
and reports the fault to the UGM The PM detects that the lift/swing center tap
voltage is between 3.31 and 3.75 volts and no
longer reports the fault to the UGM
22 21 LIFT/SWING LOCKED - JOYSTICK MOVED
BEFORE FOOTSWITCH The machine is in Platform Mode and the Lift and/
or Swing controls are not in the neutral position
immediately following Start Up -OR- The
machine is in Platform Mode and a proper
machine enable signal is received or DTC 2212,
2213 or 2223 is active while the Lift/Swing joy-
stick is not in the neutral position. If triggered by the Lift/Swing controls not being
in the neutral position immediately following
Start Up, then when Lift/Swing controls are
returned to neutral and the machine is not in
the Enabled state.
If triggered by proper machine enable signal
being received while the Lift/Swing controls are
not in the neutral position, then when the Lift/
Swing controls are returned to neutral or the
footswitch is released
22 22 WAITING FOR FSW TO BE OPEN Machine is in Platform Mode AND Footswitch has
been engaged since Start Up Footswitch is disengaged
22 23 FUNCTION SWITCHES LOCKED - SELECTED
BEFORE ENABLE The machine is in Platform Mode and a proper
machine enable signal is received or DTC 2212,
2213 or 2221 is active while any of the following
boom control inputs are engaged: AWDA Enable,
Tower Lift, Telescope, Platform Level, Platform
Rotate, Jib Lift (if MACHINE SETUP -> JIB = YES)
and Jib Rotate (if MACHINE SETUP -> JIB PLUS =
YES) None of the boom controls that trigger this fault
are engaged or the Footswitch is disengaged.
22 45 FUNCTION PROBLEM - JIB SWING LEFT PERMA-
NENTLY SELECTED The machine is in Platform mode and the Jib Swing
Left input = High at Startup Jib Swing Left input = LOW while the machine is
not Enabled
22 46 FUNCTION PROBLEM - JIB SWING RIGHT PER-
MANENTLY SELECTED The machine is in Platform mode and the Jib Swing
Right input = High at Startup Jib Swing Right input = LOW while the machine
is not Enabled
22 47 FUNCTION PROBLEM - PLATFORM ROTATE LEFT
PERMANENTLY SELECTED The machine is in Platform mode and the Platform
Rotate Left input = High at Startup Platform Rotate Left input = LOW while the
machine is not Enabled
22 48 FUNCTION PROBLEM - PLATFORM ROTATE
RIGHT PERMANENTLY SELECTED The machine is in Platform mode and the Platform
Rotate Right input = High at Startup Platform Rotate Right input = LOW while the
machine is not Enabled
22 49 FUNCTION PROBLEM - JIB LIFT UP PERMA-
NENTLY SELECTED The machine is in Platform mode and the Jib Lift Up
input = High at Startup Jib Lift Up input = LOW while the machine is not
Enabled
22 50 FUNCTION PROBLEM - JIB LIFT DOWN PERMA-
NENTLY SELECTED The machine is in Platform mode and the Jib Lift
Down input = High at Startup Jib Lift Down input = LOW while the machine is
not Enabled
22 51 FUNCTION PROBLEM - TELESCOPE IN PERMA-
NENTLY SELECTED The machine is in Platform mode and the Telescope
In input = High at Startup Telescope In input = LOW while the machine is
not Enabled
22 52 FUNCTION PROBLEM - TELESCOPE OUT PERMA-
NENTLY SELECTED The machine is in Platform mode and the Telescope
Out input = High at Startup Telescope Out input = LOW while the machine is
not Enabled
22 57 FUNCTION PROBLEM - TOWER LIFT UP PERMA-
NENTLY SELECTED The machine is in Platform mode and the Tower Lift
Up input = High at Startup Telescope Out input = LOW while the machine is
not Enabled
22 58 FUNCTION PROBLEM - TOWER LIFT DOWN PER-
MANENTLY SELECTED The machine is in Platform mode and the Tower Lift
Down input = High at Startup Tower Lift Down input = LOW while the machine
is not Enabled
22 62 FUNCTION PROBLEM - PLATFORM LEVEL UP
PERMANENTLY SELECTED The machine is in Platform mode and the Platform
Level Up input = High at Startup Platform Level Up input = LOW while the
machine is not Enabled
22 63 FUNCTION PROBLEM - PLATFORM LEVEL
DOWN PERMANENTLY SELECTED The machine is in Platform mode and the Platform
Level Down input = High at Startup Platform Level Down input = LOW while the
machine is not Enabled
Table 6-17. Diagnostic Trouble Codes
DTC Cat DTC Num DTC Text Fault Description Solution