manualshive.com logo in svg

JLG E450A, Руководство по обслуживанию и ремонту

Поделиться
Скачать
JLG E450A Скачать руководство пользователя страница 108

SECTION 3 - CHASSIS & TURNTABLE

3-68

3121714

engine temperature shutdown 248°F (120°C) for the
engine. The signal is also used in determining if the air
glow plug should be energized.

The engine oil temperature sensor is connected to the
engine/generator controller at pins J2-8 and J2-19.

The engine oil temperature sensor is located on the left
side of the engine.

Alternator Output Current Sensor

The alternator output current sensor provides a signal pro-
portional to the output current of the alternator to the
engine/generator controller. The output current is regu-
lated at 45ADC.

The alternator output current sensor is connected to the
engine/generator controller at pins J2-21, J2-31 and J2-32.

The alternator output current sensor is located inside the
rear cover of the alternator.

Engine Speed Sensor

The engine speed sensor provides a signal proportional to
the rotational speed of the engine to the engine/generator
controller. This signal is used by the engine/generator con-
troller to determine starter cut-out, overspeed fault and
underspeed fault. If the signal is not present at the engine/
generator controller, the unit will fault with a loss of speed
signal indication.

The engine speed sensor is connected to the engine/gen-
erator controller at pins J2-9, J2-15 and J2-20.

The engine speed sensor is located inside the recoil starter
cover at the front of the engine.

RBS Engine/Generator Controller

The control system enclosure houses the RBS engine/genera-
tor controller, which performs all control tasks associated with
the RBS.

The engine/generator controller interface is via a J2 35-pin
connector.

Table 3-5.   Controller Interface Pin Assignments

PIN

FUNCTION

1

System 48VDC

2

System  0V  DC

3

Fuel  solenoid

4

Starter  Solenoid

5

Manual  call  to  start

6

Low  oil  pressure

7

Not used

8

Engine oil temperature

9

Speed sensing input

10

RS-232 +12V

11

RXD

12

TXD

13

LED Driver GND

14

LED 48V

15

Speed sensor GND

16

Not used

17

Not used

18

- Output voltage

19

Engine oil temperature/ambient temp. + 8V

20

Speed S 8V

21

Output current sensor (GND)

22

Not used

23

RS-232 GND

24

- Field drive

25

+ Start battery

26

- Start battery

27

Pre-heat

28

Inhibit run

29

Engine temp. switch

Содержание E450A

































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды