Jinhan ADO102 Скачать руководство пользователя страница 36

Страница: 36 / 43

Measure Method:

Table2-7 Multimeter

Operation Key Function

Key

Description

Multimeter

Press this key to enter Multimeter Mode.

Press “ ” or “ ” to select Mesure Type

Press “ ” or “ ” to tune the Range

Multimeter’s RUN/HOLD key.

Note 1:

Multimeter’s default range is "Auto" position, for manually setting the

range, first predicted your Measurements..

Note 2: Display

screen show flashing “

”means Multimeter is

running;” MANU” means manually set the range.

⒈

DC and AC Voltage measuring

①

The Black Pen connect to the COM interface on the top of the device(the

black interface),and the Red Pen connect to VΩ interface(the red
interface)

②

Press “ON/OFF” key until the system is started, then press “Multimeter”

key to switch to Multimeter Function.

③

Press “ ” or “ ” to select “DC voltage” or “AC Voltage” measuring.”DC

Voltage” has a Shortcut,”F1”.

④

Connect the test pen to the measured voltage, the device will read the

value and show on the screen (it can also read negative value.).AC Voltage
has no polarity. This

device’s default Range is “Auto”, you can press “ ” or

“ ” to change the Range.

⒉

Resistance measuring

①

Press “ ” or “ ” to select Resistance mesuare.it has a shortcut,”F2”.

②

Put the pen on the two side of the resistor, device

can read it’s value.

Maybe you should set the Range manually.

⒊

Capacitance measuring

①

Press “ ” or “ ” to select Capacitance mesuare.

②

put the pen on the two side of the capacitance, device

can read it’s value.

Note: Capacitance measuring can’t set Range.

⒋

Diode and Buzzer-off measuring

①

Press

“ ” or “ ” key to select “Diode” or “Buzzer-off” measuring. Buzzer-off

measuring has a shortcut ,”F3”.

②

Put the pen on the two side of the Diode or the line, device

can read it’s value.(The

value when measuring

diode, it’s diode Conduction voltage drop)

③

When

mesuareing resistance is below 60Ω, buzzer alams.

Attention:

a. The device has forward and reverse voltae, when the diode connected reversed, the

value is negative.

Содержание ADO102












































Результаты поиска

Содержание ADO102

Отзывы:

Бренды по названию

Популярные бренды

Jinhan ADO102, Руководство пользователя

Результаты поиска

Содержание ADO102

Отзывы:

Бренды по названию

Популярные бренды