JetStor FX Series Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 117

background image

System Components Overview

17

11

10GbE iSCSI (RJ45) Port 2

12

12Gb/s Mini SAS HD Port 1

13

12Gb/s Mini SAS HD Port 2

INFORMATION:







Console cable (NULL modem cable) to connect from console port of
the storage system to a RS 232 port on the management PC. The
console settings are on the following: Baud rate: 115,200, 8 data bit,
no parity, 1 stop bit, and no flow control; terminal Type: vt100.

If the

JetStor FX

chassis is configured with a single controller module,

the controller module MUST be installed in the upper slot.

JetStor FX

series supports traditional UPS via a serial port and

network UPS via SNMP. If using the UPS with a serial port, connect
the system to the UPS via the included cable for communication. (The
cable plugs into the serial cable that comes with the UPS.) Then set
up the shutdown values for when the power goes out.

For a greater understanding of the related color and the behavior of the controller module,
please refer to the chapter 5.2,

Rear Panel LEDs

section in the LED Descriptions chapter.

2.5.

Power Supply Unit

All

JetStor FX

series models are equipped with two redundant and hot swappable PSUs

(Power Supply Units). The PSU for 3U/4U systems and 2U systems are the same, but the
installation direction is different. (If you pull out the PSU from the system chassis, for 4U/3U
system, the sticker on the PSU will be at down side; for 2U system, the sticker will be at right
side).The images and the table below illustrate the location of PSU in the LFF or SFF system.

«
...
31
32
33
34
35
...
»

Содержание FX Series






















































































































Отзывы:

Нет отзывов

Похожие инструкции для FX Series

Home Garden Pub

Бренд: Fishers Woodscraft Страницы: 8

A16F-R2431 Galaxy Raid

Бренд: Rorke Data Страницы: 110

Бренд: morse Страницы: 6

Бренд: Olixir Страницы: 2

Бренд: 80/20 Страницы: 3

SiliconEdge Blue Series

Бренд: Western Digital Страницы: 2

Бренд: Thecus Страницы: 130

1 GB Microdrive Storage Card

Бренд: IBM Страницы: 2

Бренд: IBM Страницы: 11

CinemaStar 5K1000

Бренд: Hitachi Страницы: 12

Deskstar 180GXP

Бренд: Hitachi Страницы: 2

Deskstar 120GXP

Бренд: Hitachi Страницы: 2

Adaptable Modular Storage 2000

Бренд: Hitachi Страницы: 24

Deskstar 7K1000.B

Бренд: Hitachi Страницы: 2

Бренд: Hitachi Страницы: 47

Бренд: Hitachi Страницы: 2

Deskstar 7K4000

Бренд: Hitachi Страницы: 3

Deskstar 180GXP

Бренд: Hitachi Страницы: 247

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды