JetStor FX Series Скачать руководство пользователя страница 102

Страница: 102 / 117

The following figure is the example of one port failed of the 10GbE iSCSI host card.

Figure 6-17

Example of a Failed Port on the 10GbE iSCSI Host Card

The following content and images are detailed steps of removing a host card from the
system.



Remove the controller module first. For detailed steps

of removing a controller module;

please refer to the chapter 6.1,

Removing / Installing the Controller Module

section.



Press the host card release button and disconnect the host card with the connector in
the controller cage.



Pull the host card out until it is free from the controller cage.



Install the substitute host card. The detailed steps of installing a host card; please refer
to the chapter 3.3,

Installing the Optional Host Cards

section.



Install the dummy host card cage in the empty host card slot and tighten two screws.



Repeat the procedures above if there are other host cards need to be removed.



To ensure the system cooling, please install all dummy host adapter card cages if host
cards are removed.

Содержание FX Series






















































































































Результаты поиска

Содержание FX Series

Отзывы:

Похожие инструкции для FX Series

Бренды по названию

Популярные бренды

JetStor FX Series, Руководство по оборудованию

Результаты поиска

Содержание FX Series

Отзывы:

Похожие инструкции для FX Series

Бренды по названию

Популярные бренды