JetStor FX Series Скачать руководство пользователя страница 105

Страница: 105 / 117

Quick Maintenance

TIP:

The flash module of Cache-to-Flash is hot swappable, but you must press
attention button until the flash module status LED is blinking before
removing the flash module from the system chassis.

The following content and image are detail steps of removing the flash module.



Press attention button of flash module until the flash module status LED is blinking.

Figure 6-23

Pressing Attention Button of the Flash Module



Press the release button of flash module and pull it out until it is free from system
chassis.



Install the substitute flash module. The detailed steps of installing the flash module,
please refer to the chapter 3.4,

Installing the Optional Cache-to-Flash Module

section.



Install the dummy cache-to-flash cage and then use a Phillips screw driver to tighten it.

Содержание FX Series






















































































































Результаты поиска

Содержание FX Series

Отзывы:

Похожие инструкции для FX Series

Бренды по названию

Популярные бренды

JetStor FX Series, Руководство по оборудованию

Результаты поиска

Содержание FX Series

Отзывы:

Похожие инструкции для FX Series

Бренды по названию

Популярные бренды