background image

 

27.  Never leave the machine running unattended. 

Turn the power off and do not leave the 
machine until it comes to a complete stop. 

28. Remove loose items and unnecessary work 

pieces from the area before starting the 
machine. 

 

 

 

Familiarize yourself with the following safety notices used in this manual. 

 

This means that if precautions are not heeded, it may result in minor injury and/or 

possible machine damage.

 

 

 

This means that if precautions are not heeded, it may result in serious or even fatal 

injury. 

 

4.0

  About this manual 

This manual is provided by JET for the JET Table Powerfeed. This manual contains instructions on installation, 
safety precautions, general operating procedures, maintenance instructions and parts breakdown. Your 
powerfeed has been designed and constructed to provide years of trouble-free operation if used in accordance 
with instructions set forth in this document.  

If there are questions or comments, please contact your local supplier or JET. JET can also be reached at our 
web site: www.jettools.com. 

Retain this manual for future reference. If the powerfeed transfers ownership, the manual should accompany it. 

 

 

 

 

Содержание TPFA-X

















Отзывы: