background image

 

8

5.4.1

  Hoist lifting method 

1. 

Position straps around lathe bed. 

IMPORTANT:

 Do 

not

 place straps around 

spindle, near levers, knobs or other parts that 
can be damaged when lifting. 

2.  Position lathe onto legs and secure with 

screws and washers (HP001/2/3, Figure 5-3) 
using 6mm hex key.  

3. Tighten 

screws 

firmly. 

 

Figure 5-3:  installing legs 

5.4.2

  Manual lifting method 

 

Use help from an assistant for 

the following procedures.

 

1.  Unscrew stud (see O, Figure 5-6) from each 

end of bed. (Note: studs can be stored in one 
of the threaded holes in lathe legs.) 

2.  Remove headstock, tailstock and tool rest 

support from bed. (Refer to 

sect. 7.0

 for 

detailed instructions on adjusting and 
removing these items.) 

3.  Carefully turn bed upside down. Place a mat or 

cardboard beneath it to prevent scratching the 
bed ways. 

4. Install legs with screws and washers 

(HP001/2/3, Figure 5-3) using 6mm hex key. 
Tighten screws firmly. 

5.  Raise bed and leg assembly right-side up.

 

 

6.  Rotate adjustable feet (Figure 5-2) as needed 

to establish level for the lathe. Tighten hex nut 
on each foot against leg casting. 

7.  Install headstock, tool support and tailstock, 

and both studs (O, Figure 5-6). 

5.5

  Tool shelf 

The tool shelf (N) can be mounted to either end of 
lathe with screws and washers (HP004/5). 

5.6

  Guard (optional accessory) 

4mm hex key required. 

The guard (part no. 719002) is optional and 
purchased separately. See our website for 
information. 

1.  Loosen set screw on outer collar (shown in 

Figure 5-4) with 4mm hex key. Slide outer 
collar off the guard support rod. 

2.  Insert guard support rod into mounting bracket 

at rear of headstock. You will have to lift up on 
spring pin, as shown, to slide guard support 
rod into mounting bracket. Release spring pin 
and it will snap into position as you slide 
support rod farther in. 

3.  Install outer collar and tighten set screw. 

4.  The guard can be pivoted to one of two 

positions: Operating mode, or tilted back for 
stock loading (Figure 5-5).  

5.  Pull up on spring pin, and begin tilting guard, 

then release spring pin. When guard reaches 
either of the two positions, spring pin will 
engage. 

 

Figure 5-4:  installing guard (optional) 

 

Figure 5-5:  guard (optional) tilted back 

 

5.7

  Bed extension (optional 

accessory) 

8mm hex key required. 

The 20” bed extension (p/n 719401) is optional and 
purchased separately. See our website for 
information. 

Содержание JWL-1840DVR













































Отзывы: