Jet JJ-6CSDX Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 44

background image

8

Unpacking

This unit is shipped in two cartons. Open both
cartons and check for shipping damage. Report
any damage immediately to your distributor and
shipping agent. Do not discard any shipping
material until the Jointer is assembled and running
properly.

Compare the contents of your cartons with the
following parts list to make sure all parts are intact.
Missing parts, if any, should be reported to your
distributor. Read the instruction manual thoroughly
for assembly, maintenance and safety instructions.

Stand Carton

1  Stand with Motor
1  Stand Cover with Mounting Hardware
1  Dust Chute with Mounting Hardware
1  Pedestal Switch with Mounting Hardware

(JJ-

6HHDX only)

Main Unit Carton

1 Bed

Assembly

1 Fence

Assembly

1 Cutterhead Guard (A)
1 Belt Guard (E)
1 V-Belt

(D)

4  1/4-20 x 1/2 Pan Head Screws (L)
4  1/4 Flat Washers (M)
1  Lock Handle, Flat Washer, and Lock Nut for

Fence (G)

1  Fence Handle (F)
3  Lock Bolts (B)
3  3/8" Lock Washers (C)
2  Handwheel Assembly (N)
2  Push Blocks (K)
1  Operating Instructions and Parts Manual
1 Warranty

Card

Tools Included for JJ-6CSX

1   12/14mm Open End Wrench (O)
1  8/10mm Open End Wrench (P)
1  3mm Hex Wrench (Q)

Tools Included for JJ-6CSDX

1   12/14mm Open End Wrench (O)
1  8/10mm Open End Wrench (P)
1  3mm Hex Wrench (Q)
1 4mm

T-Hex

Wrench

1 8mm

Hex

Wrench

Tools included for JJ-6HHDX:

1   12/14mm Open End Wrench (O)
1  8/10mm Open End Wrench (P)
1  3mm Hex Wrench (Q)
1 6mm

Hex

Wrench

2 Star Point Screwdrivers (R)
5 Knife

Inserts

(S)

10 Knife Insert Screws (T)

Stand Carton

Main Unit Carton

Tools included for Model JJ-6HHDX only

«
...
6
7
8
9
10
...
»

Содержание JJ-6CSDX













































Отзывы:

Нет отзывов

Похожие инструкции для JJ-6CSDX

Бренд: Yokota Страницы: 8

Бренд: Ganz Страницы: 8

Бренд: Wacker Neuson Страницы: 48

Бренд: Q-tran Страницы: 5

Бренд: tacwise Страницы: 12

Бренд: Eastwood Страницы: 8

Бренд: Eastwood Страницы: 8

Бренд: Franke Страницы: 89

Бренд: Conrad Electronic Страницы: 5

Dr.Peters EPG-5-ULTRA

Бренд: Glomar Страницы: 13

DIMENSION CS Series

Бренд: Puls Страницы: 27

Бренд: ROCKSOLAR Страницы: 12

Бренд: Paslode Страницы: 32

Бренд: Parker Страницы: 6

Бренд: Gallagher Страницы: 22

Бренд: Vaterra Страницы: 4

Бренд: Wacker Neuson Страницы: 112

Бренд: Laguna Tools Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды