Jet JJ-6CSDX Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 44

background image

6

Familiarize yourself with the following safety notices used in this manual:

This means that if precautions are not heeded, it may result in minor injury and/or

possible machine damage.

This means that if precautions are not heeded, it may result in serious injury or possibly

even death.

- - SAVE THESE INSTRUCTIONS - -

On-Off Switch Padlock

The jointer is equipped with a push-button
switch that will accept a safety padlock (see
figure – not included). To safeguard your
machine from unauthorized operation and
accidental starting by young children, the use of
a padlock is highly recommended. JET model
PD-LK-1 (Stock No. 709012) is available from
your local authorized JET distributor or by calling
JET Equipment & Tools at the phone number on
the cover of this manual.

Model PD-LK-1 On-Off Switch Padlock

Introduction

This manual is provided by WMH Tool Group covering the safe operation and maintenance procedures
for Models JJ-6CSX, JJ-6CSDX and JJ-6HHDX Jointers. This manual contains instructions on
installation, safety precautions, general operating procedures, maintenance instructions and parts
breakdown. This machine has been designed and constructed to provide years of trouble free operation if
used in accordance with instructions set forth in this manual. If there are any questions or comments,
please contact your local supplier or WMH Tool Group, or visit our web site: www.jettools.com.

«
...
4
5
6
7
8
...
»

Содержание JJ-6CSDX













































Отзывы:

Нет отзывов

Похожие инструкции для JJ-6CSDX

Бренд: ZALMAN Страницы: 7

Бренд: ELC Страницы: 12

Бренд: Wacker Neuson Страницы: 62

Бренд: B&B Electronics Страницы: 6

Standard iControl

Бренд: Nordson Страницы: 6

Бренд: TREND Страницы: 19

POWERPLUS POWX1331LI

Бренд: VARO Страницы: 13

Бренд: Athena Power Страницы: 10

Бренд: Powerfix Profi Страницы: 10

Бренд: Pulsar Страницы: 4

Бренд: Wacker Neuson Страницы: 74

Бренд: Fein Страницы: 118

Бренд: Facom Страницы: 2

Бренд: B&K Страницы: 2

Бренд: Lacme Страницы: 12

Бренд: Joto Страницы: 16

Бренд: coocazoo Страницы: 18

Бренд: Milwaukee Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды