background image

 

3

Table of Contents

 

Warranty and Service .............................................................................................................................. 2

 

Table of Contents .................................................................................................................................... 3

 

Warnings................................................................................................................................................. 4

 

Introduction ............................................................................................................................................. 6

 

Specifications .......................................................................................................................................... 7

 

Unpacking ............................................................................................................................................... 8

 

Assembly ................................................................................................................................................ 9

 

Electrical ............................................................................................................................................... 12

 

Adjustments .......................................................................................................................................... 13

 

Operating Controls ................................................................................................................................ 22

 

Operation .............................................................................................................................................. 22

 

Maintenance.......................................................................................................................................... 25

 

Lubrication............................................................................................................................................. 27

 

Troubleshooting Operating Problems..................................................................................................... 28

 

Troubleshooting Mechanical and Electrical Problems............................................................................. 29

 

Optional Accessories ............................................................................................................................. 29

 

Parts ..................................................................................................................................................... 30

 

Fence – Parts All Models ................................................................................................................... 30

 

Fence – Assembly All Models............................................................................................................. 31

 

Stand – Parts, JJ-6CSX and JJ-6CSDX ............................................................................................. 32

 

Stand – Parts, JJ-6HHDX only ........................................................................................................... 34

 

Stand – Assembly, JJ-6HHDX only .................................................................................................... 35

 

Bed – Parts All Models....................................................................................................................... 36

 

Cutterhead – Parts and Assembly JJ-6CSX ....................................................................................... 38

 

Cutterhead – Parts and Assembly JJ-6CSDX..................................................................................... 39

 

Cutterhead – Parts and Assembly JJ-6HHDX..................................................................................... 40

 

Wiring Diagram – All Models .............................................................................................................. 41

 

 

The above specifications were current at the time this manual was published, but because of our policy of 
continuous improvement, WMH Tool Group reserves the right to change specifications at any time and 
without prior notice, without incurring obligations. 

Содержание JJ-6CSDX













































Отзывы: