manualshive.com logo in svg

Jet JJ-6CSDX, Инструкция по эксплуатации и каталог запасных частей

Щоб отримати безкоштовний посібник з використання для продукту Jet JJ-6CSDX з детальними характеристиками, завантажте його з офіційного веб-сайту manualshive.com. Насолоджуйтесь якісним та ефективним використанням цього інструменту для роботи з деревиною.

Поделиться
Скачать
background image

 

36 

Bed – Parts All Models 

Index No.  Part No. 

Description 

Size 

Qty. 

1............... JI-T01W ...................Base...................................................................................................... 1 
2............... JI-T02W ...................Front Table (JJ-6CSX)........................................................................... 1 
................. JJ6CSDX-402 ..........Front Table (JJ-6CSDX) ........................................................................ 1 
3............... JI-T03W ...................Rear Table (JJ-6CSX) ........................................................................... 1 
................. JJ6CSDX-403 ..........Rear Table (JJ-6CSDX)......................................................................... 1 
4............... JI-T04 ......................Gib ........................................................................................................ 2 
5............... JH-T30.....................Lock Screw............................................................................................ 2 
6............... TS-0267091 .............Set Screw...........................................................1/4”-20x1”................... 5 
7............... TS-0561011 .............Hex Nut ..............................................................1/4”-20........................ 5 
8............... JI-T07W ...................Ball Crank.............................................................................................. 1 
9............... JI-T06 ......................Shoulder Pin.......................................................................................... 2 
10............. TS-0680061 .............Flat Washer........................................................1/2”............................. 2 
11............. PJ882-118 ...............Hex Nut ..............................................................1/2”-12........................ 2 
12............. JH-T11.....................Pivot Pin................................................................................................ 2 
13............. JJ6CSX-413.............Handwheel Assembly ............................................................................ 2 
16............. TS-0267041 .............Set Screw...........................................................1/4”-20x3/8”................ 2 
17............. JH-T16.....................Bushing ................................................................................................. 2 
18............. JH-T17.....................Washer.................................................................................................. 4 
19............. JH-T18.....................Adjusting Nut......................................................................................... 2 
20............. JH-T19.....................Adjusting Screw..................................................................................... 2 
21............. 5F-E108...................Pin......................................................................Ø3x24 ........................ 2 
22............. JH-T20.....................Lock Knob ............................................................................................. 2 
23............. JH-T21.....................Lock Knob ............................................................................................. 2 
24............. TS-0270031 .............Set Screw...........................................................5/16”-18x3/8”.............. 2 
25............. JH-T12W .................Ball Crank.............................................................................................. 1 
26............. JH-T22.....................Cutterhead Guard.................................................................................. 1 
27............. JH-T23.....................Guard Post ............................................................................................ 1 
28............. JH-T24.....................Retaining Washer .................................................................................. 1 
29............. JH-T25.....................Spring.................................................................................................... 1 
30............. JH-T26.....................Spring Knob .......................................................................................... 1 
31............. JH-T27.....................Retainer ................................................................................................ 1 
32............. TS-081B042.............Screw.................................................................#8-32x5/8”.................. 3 
33............. JC-T17.....................Pointer................................................................................................... 1 
34............. TS-081B012.............Screw.................................................................#8-32x1/4”.................. 1 
35............. JJ6-19......................Depth Scale........................................................................................... 1 
36............. JJ6-01CS.................Warning Label ....................................................................................... 1 
37............. JJ6-02CS.................I.D Label (JJ-6CSX)............................................................................... 1 
................. JJ6CSDX-437 ..........I.D Label (JJ-6CSDX) ............................................................................ 1 
................. JJ6HH-437...............I.D Label (JJ-6HHDX) ............................................................................ 1 
38............. JEJ-B14W................Fence Base (JJ-6CSX) .......................................................................... 1 
38A .......... JJ6CSDX-438 ..........Fence Base (JJ-6CSDX)........................................................................ 1 
39............. JED-B02 ..................Key........................................................................................................ 1 
40............. 5FF-J12 ...................Spring Pin...........................................................Ø4x20 ........................ 1 
41............. TS-0680041 .............Flat Washer........................................................3/8”............................. 1 
42............. TS-0680041 .............Flat Washer........................................................3/8”............................. 1 
43............. TS-0209071 .............Socket Head Cap Screw.....................................3/8”-16x1-1/2”............. 2 
44............. JEY-B01 ..................1/8” Set Block........................................................................................ 1 
45............. JEA-B06 ..................Stud ...................................................................................................... 1 
46............. JEA-B08 ..................Spring.................................................................................................... 1 
47............. JEA-B09 ..................Stud ...................................................................................................... 1 
48............. 5DF-B05 ..................Knob ..................................................................................................... 1 
49............. 5CO-D09B ...............Lock Handle .......................................................1/4”-20x7/8”................ 1 
50............. TS-0208041 .............Hex Socket Cap Screw.......................................5/16”-18x3/4”.............. 3 
51............. 708815 ....................Push Block ............................................................................................ 2 
52............. TS-1533032 .............Screw.................................................................M5x0.8Px10 ............... 1 
53............. TS-1550021 .............Flat Washer........................................................M4.............................. 1 

Содержание JJ-6CSDX













































Отзывы:

Нет отзывов

Похожие инструкции для JJ-6CSDX

Makita BTW074 Technical Information preview
BTW074
Бренд: Makita Страницы: 15
Makita GS5000 Instruction Manuals preview
GS5000
Бренд: Makita Страницы: 12
Balcrank Signature Series Operation, Installation, Maintenance And Repair Manual preview
Signature Series
Бренд: Balcrank Страницы: 12
Makita M432 Parts Breakdown preview
M432
Бренд: Makita Страницы: 1
Gechter 2,5 HKPE Translation Of The Original Operating Manual preview
2,5 HKPE
Бренд: Gechter Страницы: 60
NSI Solutions SL3-TPKIT-1 Instruction preview
SL3-TPKIT-1
Бренд: NSI Solutions Страницы: 10
Performance Tool M582DB Owner'S Manual preview
M582DB
Бренд: Performance Tool Страницы: 6
EFLOW eFlow 104N Series Installation Manual preview
eFlow 104N Series
Бренд: EFLOW Страницы: 16
Ace ATK-200 Technical Sheet preview
ATK-200
Бренд: Ace Страницы: 4
SMC Networks SMCRPU14 Specifications preview
SMCRPU14
Бренд: SMC Networks Страницы: 2
Akyga AK-ND-73 User Manual preview
AK-ND-73
Бренд: Akyga Страницы: 4
SW-Stahl 64340L Instruction Manual preview
64340L
Бренд: SW-Stahl Страницы: 17
Clearaudio Accurate Power Generator User Manual preview
Accurate Power Generator
Бренд: Clearaudio Страницы: 10
Cessna R172K 1980 Pilot Operating Handbook preview
R172K 1980
Бренд: Cessna Страницы: 122
Hewlee HL-300B Instruction Manual preview
HL-300B
Бренд: Hewlee Страницы: 8
H3C PS-2202-11L Manual preview
PS-2202-11L
Бренд: H3C Страницы: 6
RIDGID SC-60C Instructions preview
SC-60C
Бренд: RIDGID Страницы: 2
Samlexpower SEC-40BRM-230 Owner'S Manual preview
SEC-40BRM-230
Бренд: Samlexpower Страницы: 24

Бренды по названию

Популярные бренды

Загрузить еще бренды