4
Use suitable table extensions and
supporting aids for difficult to handle
workpieces.
Never cut pieces that are too small.
During cutting operation the
workpiece must firmly be pressed
against the table surface.
Do not perform any operation
freehand.
Remove cut and jammed workpieces
only when motor is turned off and the
machine is at a complete standstill.
Do not reach under the scroll saw
table when the motor is running.
Install the machine so that there is
sufficient space for safe operation
and workpiece handling.
Keep work area well lighted.
The machine is designed to operate
in closed rooms and must be placed
stable on firm and levelled ground.
Make sure that the power cord does
not impede work and cause people to
trip.
Keep the floor around the machine
clean and free of scrap material, oil
and grease.
Stay alert!
Give your work undivided attention.
Use common sense.
Keep an ergonomic body position.
Maintain a balanced stance at all
times.
Do not operate the machine when
you are tired.
Do not operate the machine under
the influence of drugs, alcohol or any
medication. Be aware that medication
can change your behaviour.
Keep children and visitors a safe
distance from the work area.
Never reach into the machine while it
is operating or running down.
Never leave a running machine
unattended. Before you leave the
workplace switch off the machine.
Do not operate the electric tool near
inflammable liquids or gases.
Normal brushfire might ignite.
Observe the fire fighting and fire alert
options, for example the fire
extinguisher operation and place.
Do not use the machine in a dump
environment and do not expose it to
rain.
Wood dust is explosive and can also
represent a risk to health.
Dust form some tropical woods in
particular, and from hardwoods like
beach and oak, is classified as a
carcinogenic substance.
Always use a suitable dust extraction
device
Before machining, remove any nails
and other foreign bodies from the
workpiece.
Specifications regarding the
maximum or minimum size of the
workpiece must be observed.
Do not force the power tool. It will do
a better and safer job and give you
much better service if it is used at the
rate for which it was designed.
Never operate with the guards not in
place – serious risk of injury!
Connection and repair work on the
electrical installation may be carried
out by a qualified electrician only
Always unwind any extension cords
fully.
Damaged extension cords replace
immediately.
Do not use the power tool if the
ON/OFF switch does not turn the
power tool ON and OFF.
Make all machine adjustments or
maintenance with the machine
unplugged from the power source.
Remove defective saw blades
immediately.
3.3 Remaining hazards
When using the machine according to
regulations some remaining hazards
may still exist
The moving saw blade in the work
area can cause injury.
Broken saw blades can cause
injuries.
Thrown workpieces can lead to injury
Wood chips and sawdust can be
health hazards. Be sure to wear
personal protection gear such as
safety goggles ear- and dust
protection.
Use a suitable dust exhaust system.
The use of incorrect mains supply or
a damaged power cord can lead to
injuries caused by electricity.
4. Machine specifications
4.1 Technical data
Saw blade length, pin type
127mm
Blade stroke
15mm
Blade speed
400~1600 SPM
Max cutting height at 90°
50mm
Table size
410x253mm
Table tilt
0°/45°left
Throat
406mm
Dust port diameter
35mm
Overall (LxWxH)
620x285x325mm
Weight
11 kg
Mains
230V ~1L/N/PE 50-60Hz
Motor power
90W
Reference current
0,6 A
Extension cord
H05VV-F 3G1mm²
Installation fuse protection
10A
4.2 Noise emission
(Inspection tolerance 4 dB)
Acoustic power level
(according to EN ISO 3746):
Idling
LwA 79,2 dB(A)
Acoustic pressure level
(according to EN ISO 11202):
Idling
LpA 72,1 dB(A)
The specified values are emission
levels and are not necessarily to be
seen as safe operating levels. This
information is intended to allow the
user to make a better estimation of
the hazards and risks involved.
4.3 Content of delivery
1 Scroll saw
1 Transparent blade guard
1 Air blower
1 Allen key 4mm
1 Allen key 3mm
Set of 5 saw blades
Operating manual
Spare parts list
4.4 Scroll saw description
Fig 1
