14 | Maintenance Instructions TOPAX DX | BA-40100-0-V04
Chapter 4: Installation
4.7 Operation and keyboard layout
①
②
③
④
⑤
⑥
Fig. 4.15: TOPAX
®
DX device with control panel. The keys are integrated in a
glass keyboard and react to contact.
Keys
Function
Crossed arrow keys
• Menu change-over in the menu „service“;
• Change-over between the individual numbers
• Numerical values change, parameter adjust
Switching between the individual menu options
takes place in each case on depressing the key.
Entering and changing numerical values take
place continuously
„OK“ between the
arrow keys
Input information are received and saved. Suc-
cessful saving is notified by a longer beep
Function key
①
:
„ESC“
Leave the menu or one level back without saving
Function key
①
:
„ESC“
(hold 5 secondsn)
Return to the main menu
Buttons
②
-
⑥
Functions are indicated in the display
If no operation takes place, the automatic controller turns back
into the measuring mode after approx. 5 minutes. Changed pa-
rameters, which were not confirmed with the “OK” key, are not
stored.
Exception: During the calibration and with the configuration no
“time out” takes place!
NOTE!
If no values are to be changed, “ESC” can be pressed
and the selected menus left at any time. Changed
values are confirmed with the “OK” button. If the
changed values are not saved with the “OK” button,
the device functioning goes on with default settings.
Exception: Clock and timer settings.
Basically:
• The values can be changed only within the permissible
range of values.
• The function of the key is signalled with a tone.
• Some functions can be protected by a password against
unauthorized access (see Chapter 16, Menu 5.9 „pass-
word“).
4.8 Initial operation and configuration
Switch on the power.
TOPAX DX is programmed by the manufacturer based on custom-
ers’ specs before shipment and is supplied along with a terminal
connection diagram. Ineffective or impossible configurations (for
instance double assignment of the outputs) are not admissible.
Failure of the customer to supply instructions on his purchase
order, TOPAX DX shall be programmed by the manufacturer to
the standard default settings (see Chapter 19).
For the initial start-up the operator has to configure the TOPAX
DX and set its sensors and the installed actuating elements as
well as set special functions. The relevant in- and outputs of the
TOPAX DX are automatically chosen based on this information
and the relevant connecting terminals are shown.
After a successful configuration the TOPAX DX starts up with a
standard display (see chapter 16). A subsequent renewed con-
figuration can be carried out via the Service-Menu (see chapter
16, menu 5 “Configuration”).
IMPORTANT!
For a better overview, all menus are shown on the
display with an ID-number marked on the bottom line
on the left.(see Fig. 4.16).
Choice of Language
After a short hardware test the TOPAX DX during the initial start-
up, the TOPAX DX displays the Home page for Configuration
(see diagram 4.16). This screen is shown until a language has
been chosen by pressing the key
②
(German),
③
(English),
⑤
(French) or
⑥
(further languages “>>”) – see diagram 4.15 and
4.16.
Lutz-Jesco GmbH
Am Bostelberge 19
30900 Wedemark
Deutsch
English
Francais
0.1
Software Version: ...........
TOPAX DX Start
Fig. 4.16: Home page for the configuration of language choice.
Further languages – MMC Memory card
Besides the fixed installed languages of German and English
there is other language data for the TOPAX DX. This can be writ-
ten on an external data storage unit, a MMC Memory card, and
then imported by the TOPAX DX. For further questions regarding
the availability of languages please ask the manufacturer.
