Jersey Jack Pinball Dialed in!, Руководство по эксплуатации

Страница: 361 / 372

Game Service & Troubleshooting E-7
To remove the steel mini post : The first step is to firmly grasp the rubber ring and pull it straight up, off of the post. The left outlane
mini post on Dialed In is screwed into an 8-32 T-nut, attached to the bottom of the playfield . Using the ratchet and 1/4", deep socket
from above, slowly unthread the post from the T-nut. Carefully pull the mini post and washer straight up, out of the playfield hole.
IMPORTANT: Apply minimal downward pressure as you loosen and remove the mini post; excessive downward pressure will push the
T-nut out of the back of the playfield (and it will likely end up in the bottom of your cabinet). If this occurs, locate the T-nut, re-insert
it into the playfield hole from underneath, align the T-nut's "teeth" with the indentations in the wood and gently tap it back into place
with a small hammer. Note: You may have to remove an RGB LED board or game assembly in order to gain access to the playfield hole.
To install the steel mini post : Slide the #8 washer onto the threaded end of the mini post and insert it into the desired playfield mount-
ing hole, from above. Carefully align the threads of the post with T-nut and begin threading it, by hand, into the hole (slowly turning
it in a CW direction). IMPORTANT: Apply minimal downward pressure as you install the mini post; excessive downward pressure will
push the T-nut out of the back of the playfield (if this occurs, refer to instructions in previous paragraph to re-install it). When it
becomes difficult to turn the post by hand, use the ratchet and 1/4", deep socket to finish the installation. When done, the post will be
all the way down to playfield surface level and firmly held in place. You should not be able to move the post at all by hand when you
are done. DO NOT OVERTIGHTEN! Lastly, install the post rubber ring, by sliding it over the top of the mini post.
To reposition the steel adjusting post
: Locate the washer and nylon stop nut for the adjusting post under the playfield. Using the
ratchet and the 11/32" open end wrench from below, loosen the nylon stop nut until the post feels free to move. Slide the adjusting
post into the new desired position in the playfield slot and hold it, from above, while you re-tighten the stop nut under the playfield.
When done, the bottom of the adjusting post should be all the way down, against the playfield surface, level and firmly held in place.
You should not be able to move the post at all by hand when you are done. DO NOT OVERTIGHTEN!
To remove the steel adjusting post : Locate the washer and nylon stop nut for the adjusting post under the playfield. Using the
ratchet and the 11/32" open end wrench from below, remove the nylon stop nut and washer from the bottom of the post screw.
Carefully pull the adjusting post straight up, out of the routed playfield slot.
To install the steel adjusting post
: Install the two rubber rings by sliding them over the top of the adjusting post. Slide the threaded
end of the adjusting post through the center of the routed slot in the playfield. Align the metal tab under the post with the slot as
you carefully push the post through the playfield. Install the #8 washer and 8-32 nylon stop nut to the threaded end of the post from
underneath. Using the ratchet and 11/32" socket, from below, slowly and carefully tighten the nylon stop nut until the adjusting post
is pulled almost all the way down to the playfield surface. Slide the post into the desired position in the playfield slot and hold it, from
above, while you finish tightening the stop nut under the playfield. When done, the bottom of the adjusting post should be all the way
down, against the playfield surface, level and firmly held in place. You should not be able to move the post at all by hand when you are
done. DO NOT OVERTIGHTEN !