JEM MARTIN Hydra Скачать руководство пользователя | Manualshive

Страница: 4 / 36

background image

4

Hydra user manual

• Do not operate the machine if the relative air humidity exceeds 80%.

Preventing injuries

• Ensure that the surface on which the machine is installed can safely hold the weight of the machine.

• Do not install the smoke heads over areas where people are present.

• Verify that the smoke heads’ temperature setting is suitable for the type of fluid in use whenever changing

fluid or resetting the default menu values.

• Smoke machines can cause condensation. Do not point the output at smooth floors. Floors and surfaces

may become slippery. Check these frequently and wipe dry as necessary to avoid any danger of slipping.

• Ensure at least 2m visibility in areas where smoke is being produced.

• Smoke fluid contains food-grade glycols in solution but may present health risks if swallowed. Do not drink

it. Store it securely. If eye contact occurs, rinse with water. If fluid is swallowed, give water and obtain
medical advice.

Preventing breathing problems

• A smoke machine can operate safely only with the smoke fluid it is designed for. Use the machine only

with fluids specified under “Smoke fluid options” on page 15 or you may cause the release of toxic gases,
presenting a severe health hazard. You will also probably damage the machine.

• Do not create dense smoke in confined or poorly ventilated areas.

• Do not expose people with health problems (including allergic and/or respiratory conditions such as

asthma) to smoke output.

• Do not point smoke output directly at a person’s face or at face height.

Disposing of this product

Jem products are supplied in compliance with Directive 2002/96/EC of
the European Parliament and of the Council of the European Union on
WEEE (Waste Electrical and Electronic Equipment), as amended by
Directive 2003/108/EC, where applicable.

Help preserve the environment! Ensure that this product is recycled at
the end of its life. Your supplier can give details of local arrangements for
the disposal of Jem products.

«
...
2
3
4
5
6
...
»

Содержание MARTIN Hydra





































Отзывы:

Нет отзывов

Похожие инструкции для MARTIN Hydra

KM 130/300 R Bp

Бренд: Kärcher Страницы: 372

Бренд: Kärcher Страницы: 16

BRC 30/15 C *JP

Бренд: Kärcher Страницы: 48

KM 130/300 R Bp

Бренд: Kärcher Страницы: 27

Бренд: Kärcher Страницы: 11

Бренд: Kärcher Страницы: 16

Бренд: Kärcher Страницы: 4

Бренд: Oh!FX Страницы: 8

C85 2018 BS NSC BASIC

Бренд: COMAC Страницы: 32

Бренд: Toyota Страницы: 55

BX2 Fastracts Extractor

Бренд: IPC Eagle Страницы: 8

Бренд: Stihl Страницы: 132

Бренд: Cameo Страницы: 52

Memory Craft 7000

Бренд: Janome Страницы: 94

Бренд: IPC Eagle Страницы: 40

APW-896N/IP-420

Бренд: JUKI Страницы: 142

AMS-221F3020RSW/AW-3

Бренд: JUKI Страницы: 163

Бренд: JUKI Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды