![background image](http://html1.mh-extra.com/html/jcm/ipro-100-sh2-rc/ipro-100-sh2-rc_operation-and-maintenance-manual_640203036.webp)
P/N 960-000164R_Rev. 3 {EDP #213631}
© 2018, JAPAN CASH MACHINE CO., LTD.
2 - 1 0
Section 2
iPRO-RC™ Series Banknote Recycler
Installation
Dispense Settings
Dispensing Banknotes from the RC1-Bin Space
and/or the RC2-Bin Space of the Recycler Unit is
possible. Banknote denomination dispensing is
predetermined by settings made for each RC Bin
Space.
When changing the dispensable Banknote denomi-
nation values, replace the Recycler Unit with
another Unit containing the different denomination
settings.
Clearing a Banknote Jam
When a Banknote is jammed in the iPRO-RC™
Unit, proceed as follows to clear it:
1. Open the Upper Guide of the iPRO’s Transport
a
).
2. Remove the jammed Banknote from the Trans-
port Path (Figure 2-8
a
).
3. If the Banknote jam location is not visible, press
the Recycler Unit’s
“Release”
Push Button (Fig-
b
) and pull the Recycler Unit out of the
Frame Assembly (Figure 2-7
c
).
4. Once the Recycler Unit is out of the Frame
Assembly, check inside the Frame Housing and
remove any jammed Banknotes that may be
inside (Figure 2-8
b
).
5. If the jammed Banknote is not visible, unlock and
open the Recycler Unit Door using the appropri-
ate Key supplied (Figure 2-7
d
); then remove the
jammed Banknote from inside either the RC1-Bin
Space, or the RC2-Bin Space of the Recycler Unit
Assembly (Figure 2-8
c
).
6. If the Banknote jam location is still not visible,
pull the Cash Box out of the Frame
e
) and remove the jammed Banknote
from inside the Frame Unit
d
).
7. Open the Cash Box Door using the appropriate
User Supplied Key(s) as shown in Figure 2-7, and
remove the jammed Banknote from inside the
e
).
Cleaning Procedure
It is important to keep the Banknote Path, Rollers,
and Belts clean. Adhering foreign objects or dirt on
the Validation Sensors may cause acceptance errors
or an acceptance rate degradation. Use a soft
lint-free Micro-fiber Cloth or a Cotton Swab to
wipe dirt and stains from the surfaces of the Optical
Sensors, Rollers and Belts. If necessary, blow
foreign objects or dirt away using a jet of
Compressed Air.
The Sensor Lenses are transparent, and made of a
Polymer material; handle with care. Repeat the
cleaning process as needed until the Banknote
Transport Paths are free of contaminants.
S
ENSOR
C
LEANING
P
ROCEDURE
Perform the following steps to clean the iPRO
™
and iPRO-RC™ Unit’s Sensors:
1. Turn the iPRO-RC™ Unit and the Host
Machine’s Power OFF.
2. Open the iPRO™ Transport Upper Guide.
3. Clean the Sensors, Lenses and Rollers within the
iPRO™ Transport Unit.
4. Pull the Recycler Unit out of the Frame Housing.
5. Clean the Recycler Unit Lenses and Rollers, and
the Rollers located in the Cash Box, as well.
NOTE: When setting the Recycler’s
denomination values; check the Banknote
sizes against the Recycler Unit’s size
limitation settings (e.g., 62-82mm widths,
120-158mm lengths), and ensure that the
correct Banknote Guides are in place for
the proper width and length. This operation
should be performed once appropriate
Operator training has been completed.
Figure 2-7
b
a
d
c
e
Key
Locks
Figure 2-7
Clearing a Banknote Jam 1
Figure 2-8
b
a
c
d
e
Figure 2-8
Clearing a Banknote Jam 2
NOTE: It is strongly recommended that
regular cleaning be performed at least once
a month.