background image

P/N 960-000164R_Rev. 3 {EDP #213631} 

© 2018, JAPAN CASH MACHINE CO., LTD. 

2 - 1 0

Section 2

iPRO-RC™ Series Banknote Recycler 

Installation

Dispense Settings

Dispensing Banknotes from the RC1-Bin Space 

and/or the RC2-Bin Space of the Recycler Unit is 

possible. Banknote denomination dispensing is 

predetermined by settings made for each RC Bin 

Space.
When changing the dispensable Banknote denomi-

nation values, replace the Recycler Unit with 

another Unit containing the different denomination 

settings.

Clearing a Banknote Jam

When a Banknote is jammed in the iPRO-RC™ 

Unit, proceed as follows to clear it:

1.  Open the Upper Guide of the iPRO’s Transport 

Unit (Figure 2-7 

a

).

2.  Remove the jammed Banknote from the Trans-

port Path (Figure 2-8 

a

).

3.  If the Banknote jam location is not visible, press 

the Recycler Unit’s 

“Release”

 Push Button (Fig-

ure 2-7 

b

) and pull the Recycler Unit out of the 

Frame Assembly (Figure 2-7 

c

).

4.  Once the Recycler Unit is out of the Frame 

Assembly, check inside the Frame Housing and 

remove any jammed Banknotes that may be 

inside (Figure 2-8 

b

). 

5.  If the jammed Banknote is not visible, unlock and 

open the Recycler Unit Door using the appropri-

ate Key supplied (Figure 2-7 

d

); then remove the 

jammed Banknote from inside either the RC1-Bin 

Space, or the RC2-Bin Space of the Recycler Unit 

Assembly (Figure 2-8 

c

).

6.  If the Banknote jam location is still not visible, 

pull the Cash Box out of the Frame 

(Figure 2-7 

e

) and remove the jammed Banknote 

from inside the Frame Unit 

(Figure 2-8 

d

).

7.  Open the Cash Box Door using the appropriate 

User Supplied Key(s) as shown in Figure 2-7, and 

remove the jammed Banknote from inside the 

Cash Box (Figure 2-8 

e

).

Cleaning Procedure

It is important to keep the Banknote Path, Rollers, 

and Belts clean. Adhering foreign objects or dirt on 

the Validation Sensors may cause acceptance errors 

or an acceptance rate degradation. Use a soft 

lint-free Micro-fiber Cloth or a Cotton Swab to 

wipe dirt and stains from the surfaces of the Optical 

Sensors, Rollers and Belts. If necessary, blow 

foreign objects or dirt away using a jet of 

Compressed Air. 
The Sensor Lenses are transparent, and made of a 

Polymer material; handle with care. Repeat the 

cleaning process as needed until the Banknote 

Transport Paths are free of contaminants.

S

ENSOR

 C

LEANING

 P

ROCEDURE

Perform the following steps to clean the iPRO

 

and iPRO-RC™ Unit’s Sensors:

1.  Turn the iPRO-RC™ Unit and the Host 

Machine’s Power OFF.

2.  Open the iPRO™ Transport Upper Guide.
3.  Clean the Sensors, Lenses and Rollers within the 

iPRO™ Transport Unit.

4.  Pull the Recycler Unit out of the Frame Housing.
5.  Clean the Recycler Unit Lenses and Rollers, and 

the Rollers located in the Cash Box, as well.

NOTE: When setting the Recycler’s 

denomination values; check the Banknote 

sizes against the Recycler Unit’s size 

limitation settings (e.g., 62-82mm widths, 

120-158mm lengths), and ensure that the 

correct Banknote Guides are in place for 

the proper width and length. This operation 

should be performed once appropriate 

Operator training has been completed.

Figure 2-7 

Clearing a Banknote Jam 1 

b

a

d

c

e

Key

Locks

Figure 2-7 

Clearing a Banknote Jam 1

Figure 2-

Clearing a Banknote Jam 2 

b

a

c

d

e

Figure 2-8 

Clearing a Banknote Jam 2

NOTE: It is strongly recommended that 

regular cleaning be performed at least once 

a month.

Содержание iPRO-100-SH2-RC



















































































































































Отзывы:

Похожие инструкции для iPRO-100-SH2-RC