P/N 960-000173R_Rev. A {EDP #229278}
© 2013, JAPAN CASH MACHINE CO., LTD.
2 8
Series Banknote Acceptor (EBA-40) Integration Guide
The External LED Display indicates various com-
binations of solid or alternating Color light flashing
conditions when any of the Standard Error and
Reject Codes listed in Table 23 through Table 25
occur.
Identify the cause and solution for an indicated
error by comparing it against each listing in Table
23. Ensure that the relative Assemblies are properly
connected and/or harnessed, and all of the Unit’s
sensors are clean before proceeding to troubleshoot
the error condition.
LED F
LASH
E
RROR
C
ODE
C
ONDITIONS
Table 23 lists the various LED Flash Error Code
causes & solutions for Banknotes
Table 22
Communication Fault Conditions
Symptoms/Error
Messages
Possible Fault Causes
Corrective Action Required
Cannot
communicate with the
Host Machine
DIP Switch settings are
incorrect.
Set all DIP Switches to OFF.
Connectors are disconnected
or loosely connected.
Firmly re-seat all of the Communication Connectors.
Damaged Connector Pins.
Check for any bent, missing or damaged Pins in the Connector Plugs and
mating Receptacles.
CPU Board is corrupted.
Exchange the CPU Circuit Board with a known good Circuit Board.
Incorrect Interface.
Verify that the correct interface between the Host Machine and the Banknote
Acceptor is being used.
LED Indication Conditions
Table 23
LED Flash Error Codes
LED
Sequence
LED Color
State
Error
Causes and Solutions
Red
(1)
Green Lit
External Flash
ROM Boot Program
ROM Check Error
The Boot Program that is supposed to run after Power is supplied is not correctly
written in ROM, or it cannot be read.
[Solution] Check that the following part is properly assembled and/or Harness
connected.
[Relative Parts] CPU Circuit Board.
If the error is not resolved, change the above related part or parts.
Red
(2)
Green Lit
External Flash
ROM Boot I/F Area
ROM Check Error
The Boot Interface Area was not written correctly or cannot be read.
[Solution] Re-download the Program. If the error is not resolved, check that the
following part is assembled and/or Harness connected.
[Relative Parts] CPU Circuit Board.
If the error is not resolved, change the above related part or parts.
External Flash
ROM Main Program
ROM Check Error
The Main Operating Program is not written into the ROM correctly, or cannot be
read.
[Solution] Re-download the Program. If the error is not resolved, check that the
following part is properly assembled and/or Harness connected.
[Relative Parts] CPU Circuit Board.
If the error is not resolved, change the above related part or parts.
Red
(3)
Green Lit
CPU Internal RAM
Check Error
RAM reading or writing was not properly performed.
[Solution] Check that the following part is properly assembled and/or Harness
connected.
[Relative Parts] CPU Circuit Board.
If the error is not resolved, change the above related part or parts.
Red
(4)
Green Lit
External SD-RAM
Error
External SD-RAM reading or writing was not properly performed.
[Solution] Check that the following part is properly assembled and/or Harness
connected.
[Relative Parts] CPU Circuit Board.
If the error is not resolved, change the above related part or parts.
Red
(5)
Green Lit
EEPROM Error
EEPROM reading, writing and/or saving was not properly performed.
[Solution] Perform the Sensor Calibration procedure. If the error is not resolved,
check that the following part is properly assembled and/or Harness connected.
[Relative Parts] CPU Circuit Board.
If the error is not resolved, change the above related part or parts.
Red
(6)
Green Lit
Downloading File
Error
Downloading files does not proceed.
[Solution] Select a file supported by the EBA Unit.
Red
(7)
Green Lit
Magnetic Sensor
Setting Abnormal
An abnormal Magnetic Sensor setting is detected.
[Solution] Check that the following part is properly assembled and/or Harness
connected. Clean the following Sensor.
[Relative Parts] Magnetic Sensor.
If the error is not resolved, change the above related part or parts.
