background image

4

JCB-MS-305SB-L

Instruction & User Manual

GENERAL SAFETY INSTRUCTIONS

Save all warnings and instructions 

for future reference. 

Work area safety 

Keep work area clean and well lit 

 Cluttered and dark areas invite accidents. 

b

  Do not operate power tools in 

explosive atmospheres, such as in the 

presence of flammable liquids, gases 

or dust. 

  Power tools create sparks which may ignite 

the dust or fumes. 

c

  Keep children and bystanders away 

while operating a power tool. 

 Distractions can cause you to lose control. 

2

 Electrical safety 

a

  Power tool plugs must match the 

outlet. Never modify the plug in any 

way. Do not use any adapter plugs 

with earthed (grounded) power tools 

  Unmodified plugs and matching outlets will 

reduce risk of electric shock. 

b  

Avoid body contact with earthed 

or grounded surfaces such as pipes, 

radiators,ranges and refrigerators.

 –  There is an increased risk of electric shock if 

your body is earthed or grounded. 

c  

Do not expose power tools to rain or 

wet conditions.

 

 Water entering a power tool will increase the 

risk of electric shock. 

d  

Do not abuse the cord. Never use 

the cord for carrying, pulling or 

unplugging the power tool. Keep cord 

away from heat, oil, sharp edges or 

moving parts. 

  Damaged or entangled cords increase the 

risk of electric shock. 

e  

When operating a power tool 

outdoors, use an extension cord 

suitable for outdoor use. 

  Use of a cord suitable for outdoor use 

reduces the risk of electric shock. 

f  If operating a power tool in a damp 

location is unavoidable, use a residual 
current device(RCD) protected supply 

  Use of an RCD reduces the risk of electric 

shock. 

Personal safety 

a  

Stay alert, watch what you are 

doing and use common sense when 

operating a power tool. Do not use 

a power tool while you are tired or 

under the influence of drugs, alcohol or 

medication. 

   A moment of inattention while operating 

power tools may result in serious personal 

injury. 

b

  Use safety equipment. Always wear 

eye protection. 

  Safety equipment such as dust mask, non-skid 

safety shoes, hard hat, or hearing protection 

used for appropriate conditions will reduce 

personal injuries. 

Read all safety warnings instructions, 
illustrations and specifications provided 
with this power tool. 

Failure to follow the warnings and instruc-
tions may result in electric shock, fire and/
or serious injury. The term “power tool” in 
the warnings refers to your mains-operated 
(corded) power tool or battery-operated 
(cordless) power tool.

WARNING!

Содержание JCB-MS-305SB-L






























Отзывы: