ENGLISH
USER MANUAL
JB SYSTEMS®
7/81
MCD200
22. FOLDER SELECTOR:
if your CD has MP3 subfolders, you can select these by simply
turning this folder selector. The display shows you the folder name. The
folder name is shown instantly when you press the folder selector shortly. Check the
next chapter for more information on the use of subfolders. When the CD doesn’t
contain subfolders, this selector is not used.
23. TRACK SELECTOR:
used to select the tracks on your CD. If your CD has MP3
subfolders, the MCD200 has two selection modes:
FOLDER MODE:
When used together with the FOLDER selector, you can only
select tracks inside the selected folder. To go to another folder just use the
FOLDER selector.
TRACK MODE:
To select track mode, just press the TRACK selector shortly: you
will be able to browse all the tracks on your CD as if no subfolders where present.
To move quickly (by 10tracks) through the CD, press the TRACK selector while
turning it forward/backward.
24. Audio output:
Output for the audio signals from the CD-player. Use the supplied
cinch/cinch cable to connect this output to a CD/line input of your mixing unit.
25. Digital out socket:
Use this connector to connect the digital signal (S/PDIF format) to
the input of a digital amplifier or digital recorder (ex. Mini disc)
26. RELAY Socket:
you can use this connecter in two ways: you can use it with the fader
start option on certain mixers or you can connect two MCD200 players together to
obtain the relay play function.
Relay play:
Use the supplied mono mini jack/jack cable to connect the RELAY
sockets of two MCD200 players together. Look further in this manual to learn how
to perform the relay play function.
Fader start:
If you are using a mixer with fader start function, use the supplied
mono mini jack/jack cable to connect the player with the fader start of the mixer.
Please note that this socket must never be connected with any voltage.
Attention:
This remote control is only compatible with certain (Synq® or Pioneer® compatible)
mixers. Mixers with remote starts functioning with a signal switched to ground will
not
work.
27. POWER ON/OFF switch:
switches the MCD200 on and off.
28. MAINS INPUT:
connect the CD player to the 230V AC mains, using the supplied
power-cord.
ENGLISH
USER MANUAL
JB SYSTEMS®
8/81
MCD200
LCD DISPLAY
1. PLAY:
appears while the unit is playing a CD.
2. PAUSE:
appears while the player is in pause or cue mode.
3. ANTI SHOCK AND BUFFER INDICATOR:
The memory status is represented on the
display by a bucket being filled up or emptied. The bucket itself represents that the
instant start function is available. If the bucket is flashing, the instant start is not
available. Each segment within the bucket represents about 2 seconds of anti shock
protection.
4. CUE:
appears when the master cue point is programmed.
5. PITCH DISPLAY:
Shows the actual percentage of speed change, selected with the
SPEED slider(15).
6. TIME BAR:
shows either time remaining or elapsed depending on the setting of the
TIME button(16). Starts flashing at the end of each track to alert the user to take action.
7. FRAME:
Shows “frame” time information of current track. (1 frame = 1/75
th
sec.)
8. SECOND:
Shows “seconds” time information of current track.
9. MINUTE:
Shows “minutes” time information of current track.
10. ELAPSED, TOTAL REMAIN:
indicates that the time shown on the display is the track
elapsed, remaining or total remaining time.
11. RELOOP:
appears when the CD has had a loop set previously. You can return to the
loop with the reloop button(5).
12. LOOP:
shows when a loop is programmed. (repeating a particular area)
LOOP Flashing:
Loop is programmed and currently playing.
LOOP stays on:
Loop is programmed but not playing.
13. SINGLE:
appears when the unit is set to play just one track at a time. When it is not
shown, the CD plays continuously through all tracks. The function is controlled by the
SGL/CTN button(17).
14. TRACK / FOLDER:
Shows current track or folder number.
15. VISUAL MARKER:
indicates the play position in frames: a full rotation equals 72
frames. The marker moves clockwise in normal play mode and counter-clockwise when
the track plays backwards. In pause mode the marker stops moving.