ENGLISH
USER
MANUAL
JB SYSTEMS®
9/52
CD200
•
EDIT A LOOP:
When a loop is playing, press OUT/EXIT button to leave the loop. Press the
OUT/EXIT button again. The loop starts playing immediately and the new endpoint
is programmed.
•
For a shorter loop:
press the OUT/EXIT button quickly.
•
For a longer loop:
wait longer before pressing OUT/EXIT.
NOTE:
You can store loops under the HOT CUE buttons. This means that you have up to 4 loops
per track to play with. In the next paragraph you learn how to store these loops.
•
STORING A MASTER CUE POINT:
There are 2 ways to set a master cue point:
•
Press the IN/R.CUE button during normal playback to set the new cue point
(“CUE on the fly”).
•
Put the player in pause and use the jog/shuttle wheel to search for the exact
location for the cue point. Once this location is found, press “IN/R. CUE” button
to set the new cue point. (or press PLAY/PAUSE button)
Once the cue point is programmed, just press the CUE button to recall it.
•
STORING A SIMPLE CUE POINT TO THE “HOT CUE” BUTTONS:
First press the MEMORY button(9) to make the unit enter hot cue memory mode
(MEMORY button is lit).
•
Press one of the four HOT CUE buttons at the right moment during normal
playback: the HOT CUE button you just pressed turns to red colour to indicate
that the desired cue point is stored. (“Cue on the fly”).
•
Put the player in pause and use the jog/shuttle wheel to search for the exact
location for the cue point. Once this location is found, press one of the four HOT
CUE buttons to set the new cue point: the HOT CUE button you just pressed
turns to red colour to indicate that the desired cue point is stored.
Once the cue point is programmed, just press the HOT CUE button to start
playback from the stored cue point.
•
STORING A LOOP TO THE “HOT CUE” BUTTONS:
This is very similar to storing a simple cue point. The only difference is that you
have to put the CD200 in loop mode first. When the loop is playing, you press the
MEMORY button to make the CD-player enter hot cue memory mode (MEMORY
button is lit). After this press one of the four HOT CUE buttons: the HOT CUE
button you just pressed turns to green colour to indicate that the loop, playing at
that moment, is stored. You can store up to 4 loops!
•
STORING HOT CUE MEMORIES TO THE PERMANENT INTERNAL MEMORY:
For each CD you can store up to 4 cue points and loops to the internal permanent
memory. At a later time you can recall these cue points and loops when you insert
the same CD again. The CD200 can hold up to 2048 (512 x 4) Cue points and
loops. Writing the contents of the HOT CUE buttons to permanent memory is very
simple: just press the MEMORY button for about 2 seconds until the display shows
“SAVING”. That’s all!
NOTE:
When you put another CD in the disc tray without first writing the current HOT CUE
memories to the internal permanent memory, they will be lost.
ENGLISH
USER
MANUAL
JB SYSTEMS®
10/52
CD200
•
RECALLING HOT CUE MEMORIES FROM PERMANENT INTERNAL MEMORY:
If you have stored permanent cue points and loops for a CD, you can choose to
recall these while reloading that CD at a later time.
•
RECALL:
Before loading the CD, just press the MEMORY button until it starts
flashing and the display shows “RECALL”. Now press the OPEN/CLOSE button
to load the CD. It takes some seconds to load the HOT CUE buttons, during this
time the display shows “RECALL”. If no permanent cue points where found, the
CD200 stops the recall process automatically.
•
DON’T RECALL:
Just insert the CD as usual and start playback. The CD200
will ignore the permanent cue point information for this CD.
•
DELETE THE “HOT CUE” BUTTONS:
This can be done in two ways:
•
Simply program a new HOT CUE, the previous will be erased.
•
Put another CD in the disc tray, the HOT CUES will be erased.
•
DELETE THE ENTIRE INTERNAL CUE MEMORY:
Turn the SEARCH Button(1) to the left (counterclockwise) and keep it in that
position while switching the CD200 on: the permanent cue memory is cleared.
CAUTION: THIS ACTION IS IRRIVERSIBLE, ALL CUE POINTS/LOOPS WILL BE DELETED!!!
•
PITCH BENDING:
This function is used to put the beats of two tracks in perfect sync. This can be
done in two ways:
•
PITCH BEND buttons: The speed increases or decreases respectively as long
as the PITCH BEND+ or PITCH BEND- button is pressed.
•
JOG WHEEL: During play mode the JOG WHEEL will temporarily bend the pitch
of the music by turning the JOG WHEEL clockwise to speed up or
counterclockwise to slowdown. The rotation speed the JOG WHEEL determines
the percent of pitch bend.
SPECIFICATIONS
Power Supply:
AC 230 V, 50Hz
Power Consumption:
14W
Output level:
1.0Vrms
@
1kHz
Frequency response:
20-20.000Hz (+/-0.5dB)
THD + noise:
0.01% @ 1kHz, 0dB
S/N Ratio (IHF-A):
>90dB @ 1kHz.
Short access time (next track):
<
1.9sec
Long access time (track 1
Æ
20):
<
3.6sec
Laser Pickup:
3spot detection 780nm
Electronic tracking:
Full automatic digital tracking.
Dimensions:
348(W) x 246(D) x 106(H) mm
Weight:
3kg
