Jaytech RDO 1000 Скачать руководство пользователя страница 2

Страница: 2 / 21

- 1 -

START BY READING THESE IMPORTANT
SAFETY INSTRUCTIONS

WARNING

•

Failure to comply with the following instructions may

result in serious personal injury or property damage.

• Read and follow all instructions carefully.

• Th

is This opener is designed and manufactured to meet

Australian Standards AS/NZS 60335.2.95:2012 and

AS/NZS 60335.1:2011 when installed correctly.

These safety alert symbols mean

WARNING

: A possible

risk to personal safety or property damage exists.

Keep garage door balanced

Do not let the garage door

opener compensate for a binding or sticking garage door.

Sticking, binding or unbalanced doors must be repaired

before installing this opener.

Do not wear rings, watches or loose clothing.

while

installing or servicing a garage door opener. Wear gloves and

suitable protective clothing where appropriate.

Содержание RDO 1000






















Результаты поиска

Содержание RDO 1000

Отзывы:

Похожие инструкции для RDO 1000

Бренды по названию

Популярные бренды

Jaytech RDO 1000, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание RDO 1000

Отзывы:

Похожие инструкции для RDO 1000

Бренды по названию

Популярные бренды