Jaytech RDO 1000 Скачать руководство пользователя страница 18

Страница: 18 / 21

- 17 -

22.SPECIFICATIONS SILENTDRIVE

Model

MR350

MR400

RD01000

Opening Speed

200MM/S

Rated Lifting Weight

(350N)

(400N)

(450N)

Max Lifting Force

600N

800N

1000N

Rated door area

18 m²

20 m²

22 m²

Max door weight

100kgs

110kgs

120kgs

Drum Rotations

5.5

Power Supply

220VAC-240VAC/50Hz -60Hz ; 110VAC-127VAC/50Hz-60Hz

Motor Type

24V DC permanent magnet

General working time

≤60s

Working Temperature

-20

℃

- +50

℃

Transmitter Frequency

433.92MHz

Coding Type

Rolling code

Coding Combination

Over 4.29 billion

Lights

24V / 12pcs LED bulbs

21.IMPORTANT INFORMATION FOR THE USER

Once the opener has been installed, the user must be informed about the risks that can arise if it is

used improperly. The user must avoid placing himself/herself in dangerous situations such as standing

within the door’s operating range when i

t is moving.

Do not

let children play near the door and keep the remote controls out of their reach.

All services, repairs or checks must be carried out by professionally qualified persons and should

be noted on a maintenance register kept by the user.

IMPORTANT NOTE:

In the case of a malfunction the user must call an authorized installer and

should not attempt the repair themselves.

Содержание RDO 1000






















Результаты поиска

Содержание RDO 1000

Отзывы:

Похожие инструкции для RDO 1000

Бренды по названию

Популярные бренды

Jaytech RDO 1000, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание RDO 1000

Отзывы:

Похожие инструкции для RDO 1000

Бренды по названию

Популярные бренды