background image

Jaypro Retractable Practice Cages - Installation and Operating Instructions

www.jaypro.com  / (800) 243-0533 / 976 Hartford Tpke, Waterford, CT 06385 USA

SUBJECT TO CHANGES IN DESIGN AND MANUFACTURING

 COPYRIGHT 2017 JAYPRO SPORTS, LLC. ALL RIGHTS RESERVED

BBC-700 REV B, RELEASED 12-29-2017

Sheet 4 of 26

1.

Key Switch Operation

OPERATING INSTRUCTIONS:

a.

Inserting the key and turning in the direction of desired travel actuates the key switch.

REGULAR EQUIPMENT MAINTENANCE:

1.     Key Switch

a.

Key switch is dual direction momentary actuated. No maintenance or upkeep should 
ever be required. For additional or replacement keys call Jaypro (you must have the key
number).

2.     Wire Rope

a.

Wire rope should be lubricated regularly to ensure long reliable life. Obtain a suitable 
wire rope lubricant from local supply or hardware store. Do not use heavy grease or 
engine oil for lubricant. A recommended penetrating lubricant is MIL-G-18458 wire rope 
grease. Lubrication is best applied at the point of the wire rope bending over the pulley 
sheave, where the strands will be temporarily and partially separated allowing the 
lubricant to penetrate fully.

b.

Inspect rope for excessive damage or broken  threads . See image below - if wire rope 
looks like any of these pictures, it s time to replace it:

Replacement hoist cables (wire ropes) can be obtained directly from Jaypro, or from a 
qualified wire rope manufacturer or supplier. Cables are 1/8  x 7/19 Galvanized Cable 
with both ends terminated with a flemished eye splices and galvanized thimbles.

c.

Figure 2:  Worn and Damaged Wire Ropes - Replacements Required

Содержание BBC-700B



























Отзывы: