![background image](http://html1.mh-extra.com/html/jayco/2016-white-hawk/2016-white-hawk_owners-manual_3567424062.webp)
SECTION 5 – SLIDE-OUT SYSTEMS
JAYCO TOWABLE
TABLE OF CONTENTS
5-
4
Low Voltage:
The inwall slide controller is capable of operating the room with as little as 8 volts. But at
these lower voltages the amperage requirement is greater. Check the voltage at the
controller. If voltage is lower than 11 volts, it is recommended that the battery be placed
on a charger until it is fully charged. It may be possible to “jump” the RV battery
temporarily to extend or retract the room. Consult Customer Service before attempting to
“jump” the auxiliary battery.
Only 1 Side Moving:
The inwall room slide has a separate motor to operate each side of the room. Does only 1
side of the room move a short distance (2 to 4 inches) and stop? Will Non-moving side
move with help? If only 1 side of the room is moving, then with another person’s
assistance press the switch to extend or retract the room while pushing the non-moving
side in the appropriate direction. On larger rooms it may be necessary to have 2 or more
people pushing the room.
Non-moving side moved manually:
Try to push the non-moving side in and out. If a motor shaft has broken then it will be
possible to move that side of the room several inches by hand. Larger rooms may require
several people to push.
Debris in the rack:
Check all 4 gear racks on the side of the room for debris.
Do the status LEDs light?
Locate the slide controller for the slideout in question. When the room slideout direction
switch is actuated, do the status LEDs light up. Check this in both the extend and retract
modes.
Manual override for the inwall slideout
The slideout system comes with an “electronic” manual override. In event the slide out
does not extend or retract follow these steps to override the system which should allow the
slideout to be retracted.
NOTE:
Fuses for the slideouts can be found in the load center and may be designated
as auxiliary or slideout motor.
1.
Locate the slideout system controllers. There should be one for each slideout on the
recreation vehicle. They are typically located in the basement compartment in the
forward section of the recreation vehicle, either on the forward wall or on the
ceiling. In some models they may be behind a cargo lined panel.
2.
The controller that has malfunctioned should have a flashing red LED indicating a
hall signal fault (will flash 8 or 9 times).
3.
Press the “mode button” six times quickly, then press a seventh time and hold for
approximately 5 seconds.
4.
The red and green LED’s will begin to flash indicating you are in override mode.
Release the mode button.
5.
Use either a wall switch, or one of the slide room switches located on the command
center panel (depending on the slideout). Press the switch toward the word IN or
RETRACT (printed next to the switch) and hold it until the unit comes in
completely.
6.
This will allow you to get the recreation vehicle to a service center to have the
slideout malfunction diagnosed.
Содержание 2016 White Hawk
