Jay-Lor 4000 TWIN AUGER Series Скачать руководство пользователя страница 22

Страница: 22 / 57

AAA-055-00084

Jaylor Operator’s Manual

- 21 -

Twin Auger Trailer Units

•

Retorque all wheel nuts, fasteners, and hardware.

•

Check that auger turns freely.

•

Check the auger. Remove all string, twine, or other entangled material.

•

Proceed with normal servicing and maintenance schedule as defined in the Maintenance

Section.

EQUIPMENT MATCHING

The machine is designed to be used with Agricultural tractors. To ensure a good performance,
the following list of specifications must be met:

1. Horsepower:

The minimum horsepower that is required for your Jaylor is explained in the ‘Mixer
Specifications’ located at the end of this document.

2. Drawbar Dimensions:

The tractor drawbar dimension must be set using the chart below.

For Standard double yoke PTO’s:

PTO

Spline

Drawbar Position (A1)

Type 1

540 rpm - 1 3/8" / 1 3/4”
(35mm / 45mm)

14.0" (356mm)

Type 2

1000rpm - 1 3/8" (35mm)

16.0" (400mm)

Type 3

1000rpm - 1 3/4" (45mm)

20.0" (500mm)

For Optional Constant Velocity (CV) PTO’s:

PTO

Spline

Drawbar Position (A1)

Type 1

540 rpm - 1 3/8" / 1 3/4”
(35mm / 45mm)

9.75" (250mm)

Type 2

1000rpm - 1 3/8" (35mm)

9.75" (250mm)

Type 3

1000rpm - 1 3/4" (45mm)

9.75" (250mm)

Содержание 4000 TWIN AUGER Series


























































Результаты поиска

Содержание 4000 TWIN AUGER Series

Отзывы:

Похожие инструкции для 4000 TWIN AUGER Series

Бренды по названию

Популярные бренды

Jay-Lor 4000 TWIN AUGER Series, Руководство оператора

Результаты поиска

Содержание 4000 TWIN AUGER Series

Отзывы:

Похожие инструкции для 4000 TWIN AUGER Series

Бренды по названию

Популярные бренды