background image

www.javad.com

  

9

3. Follow the on-screen installation instructions. 

Click Install to continue. Keep the default installation 

location or select a new location. If desired, create a 

shortcut on the computer’s desktop for quick access to 

NetView.

JAVAD GNSS NetView software provides an inter-

face  for  various  configuration,  monitoring,  and  man

-

agement functions for the receiver.

Once you have established a connection between the 

receiver and the computer/controller, you will be able 

to configure the receiver and its components, send com

-

mands to the receiver, download files from the receiv

-

er’s memory; as well as, upload new firmware, upload 

an  OAF,  and  upload  configuration  files  to  a  receiver, 

using NetView.

Establishing an RS232 Cable Connection

Using the RS232 cable, connect the serial port of 

your computer (usually COM1) to the receiver’s serial 

port A.

1. Press the power buttons on the receiver and com-

puter to turn them on.

2. Start NetView, select SER as type of connection 

mode, and specify the port the receiver is connected to.

Figure 5. 

NetView: Connection via serial port

Establishing  an USB connection

Make sure the computer has JAVAD GNSS’s USB 

driver installed (available from www.javad.com) be-

fore continuing.

1. Using the USB cable, connect the USB port on the 

receiver to a USB port on the computer.

2. Press the power buttons on the receiver and com-

puter to turn them on.

3. Start NetView and select USB as type of connec-

tion mode and select USB port ID from the list

Figure 6. 

NetView: USB connection

Configuring Receiver

Both Base and Rover receivers must be configured 

according to the desired survey method. 

In applications where real-time positioning results 

are required, the Base receiver provides the correction 

information needed to properly calculate the location 

of the Rover receiver. A Base station is normally set up 

over a known point and collects GPS/GLONASS data 

from satellites. As the receiver picks up satellite data, 

it measures the carrier and code phases to accurate-

ly compute and verify its location. Then, the receiver 

transmits this information via radio (UHF or GSM) to 

the Rover receiver. 

The Rover receiver applies correction information 

from the Base station to its current location to accu-

rately calculate one or more points. Rovers are mobile 

GNSS receivers on a survey pole or bipod that com-

pares the information from the Base station to the data 

it logs from satellites and applies correction algorithms 

to accurately calculate a new point.

In applications intended for post-processing, the re-

ceivers typically log code phase and/or carrier phase 

measurements separately from common satellites and 

during the same time interval. This data is then pro-

cessed using post-processing software (for example, 

Justin).

When configuring receivers for RTK surveying, use 

the following list to ensure the receivers are properly 

set up:

 Configure one receiver as an RTK Base station and 

the other receiver as an RTK Rover.

Configure the communication data link for transmit

-

ting and receiving corrections.

Set up the Base receiver over a known point to begin 

collecting static observation data and transmitting cor-

Содержание DELTA-3N























Отзывы: