Javad DELTA-3N, Руководство пользователя

Страница: 8 / 22

8
www.javad.com
A single external power supply with 5 pin ODU
connector or SAE connector is necessary to operate
DELTA-3N. If external power supply has only SAE
connector, Receiver-to-SAE power cable shall be used.
The external power supply needs to be Listed for US
and Certified for EU countries, it needs also to be a
Limited Power Source and have an output rated for 14.5
- 35 V DC, 2A. This may not be the same range as other
JAVAD GNSS products with which you are familiar.
To avoid the introduction of hazards when operating
and installing, before connecting of the equipment to
the supply, make sure that the supply meets local and
national safety ordinances and matches the equipment’s
voltage and current requirements.
Warning:
Never attempt any maintenance or cleaning of the
supply while plugged in. Always remove supply from AC power
before attempting service or cleaning.
If the voltage supplied is below the minimum speci-
fication, the receiver will suspend operation. If the volt -
age supplied is above the maximum specification, the
receiver may be permanently damaged, voiding your
warranty.
Make sure cords are located so that will not be stepped
on, tripped over, or otherwise subjected to damage or
stress. Do not operate equipment with a damaged cord
or plug – replace immediately. To reduce the risk of
damage to the equipment, pull by the plug body rather
than the output cord when disconnecting the equipment.
Warning:
Do not operate the supply if it has received a sharp
blow, been dropped, or otherwise damaged. Do not disassemble
the supply.
Before connecting the external power source and the
receiver, make sure that the power source matches the
receiver’s voltage and current requirements.
Powering the receiver
To check the status of the internal batteries, view the
BAT LED or check the status using JAVAD GNSS soft-
ware. Check the BAT LED for battery status.
To charge the receiver internal batteries, take the fol-
lowing steps:
• Plug the Receiver-to-SAE cable’s connector into
the power port of the receiver (14-578125-01).
• Connect the opposite end of this cable with the
battery charger’-s SAE connector (22-570101-01).
• Plug the other end of this cable into an AC outlet
with cable (14-508053-01). Leave overnight.
Cables
The DELTA-3N receiver package includes standard
communication and power cables for configuring the
receiver and providing a power source to the receiver.
• Receiver-to-computer RS232 serial cable – con-
nects the receiver’s serial port and an external device
(hand-held controller or computer) p/n 14-578103-
01
• Receiver-to-SAE power cable – connects the re-
ceiver’s power port and the power supply’s SAE
connector or the extension cable’s SAE connector
p/n 14-578101-01
• SAE-to-SAE cable extension – connects SAE con-
nectors over longer distances p/n 14-578102-01
Option Authorization File (OAF)
JAVAD GNSS issues an Option Authorization File
(OAF) to enable the specific options that customers
purchase. An Option Authorization File allows custom-
ers to customize and configure the DELTA-3N receiv -
er according to particular needs, thus only purchasing
those options needed.
Typically, all DELTA-3N receivers ship with a tem-
porary OAF that allows the receiver to be used for a
predetermined period of time. When the receiver is
purchased, a new OAF activates desired, purchased op-
tions permanently. Receiver options remain intact when
clearing the NVRAM or resetting the receiver.
Managing and Operating
Receiver using NetView
This software is available on the JAVAD GNSS web-
site. If downloading the program(s) from the website,
extract the program’s files into a folder on your hard
drive. The following sections describe installing this
software, and other sections throughout the manual de-
scribe using this software with the receiver.
Note:
Refer to the NetView Software Manual for full details
on installing and using NetView Software.
1. If downloading the program from the website, ex-
tract the program files into a folder on your hard drive.
2. Navigate to the location of the NetView program
and double-click the Setup.exe icon.