Jasic AC/DC250P Скачать руководство пользователя страница 18

Страница: 18 / 18

22. When the pulse conversion

switch is at no-pulse state, in

ARC/TIG mode, the welding

current is invariable, and there

is only maximum current.

a. The diode D24 on control panel

PK-31-A0 is damaged.

a. Check and replace it if necessary.

23. Turn on the machine, the

indicator of protection status is

on because the voltage is too

low.

a. The input voltage is too low or is

unstable.

b. The thermal switch matching socket

CON14 on control panel PK-31-A0 is

damaged.

c. The connecting cable matching socket

CON15 on control panel PK-31-A0 is in

loose connection.

d. The resistor R51/R44 or chip U6 on

control panel PK-31-A0 is damaged.

a. Check.

b. Check.

c. Check.

d. Check. Method: properly reduce

the value of resistor R44.

24. The tungsten is badly

burned out in AC mode.

a. The value of AC clean width on the panel

is adjusted too big.

a. Adjust the clean width smaller.

25. The manual control is

normal, but the pedal control

goes wrong.

a. The connecting cable matching socket

CON4 on control panel PK-31-A0 is in

loose connection.

b. Some part on control panel PK-31-A0 is

damaged.

a. Check.

b. Check if diode D23, zener diode

Z5, resistor R32/R35/R46 or

inductor L3/L4 on control panel

PK-31-A0 is damaged.

Содержание AC/DC250P



















Результаты поиска

Содержание AC/DC250P

Отзывы:

Похожие инструкции для AC/DC250P

Бренды по названию

Популярные бренды

Jasic AC/DC250P, Схематическая диаграмма

Результаты поиска

Содержание AC/DC250P

Отзывы:

Похожие инструкции для AC/DC250P

Бренды по названию

Популярные бренды