Janome myLock 134D Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 39

background image

POSITION OF LOWER LOOPER THREAD GUIDES

LOWER LOOPER THREAD GUIDE (A)

Loosen the set screw (C), and adjust the lower looper thread guide (A) so that the hole of

thread guide is in line with the groove of lower looper as shown in ** F **.

Be careful not to raise the lower looper thread guide (A) too high. Otherwise it will touch

the metal of the arm, the feed dog or the feed dog platform.

LOWER LOOPER THREAD GUIDE(B)

Loosen set screw (D) on lower looper thread guide (B). Align lower looper thread guide
(B) with the slit (H) on the lower looper drive arm (G) as shown. Tighten set screw (D).

LOOPER THREAD TAKE-UP LEVER (I)

Loosen the set screw (E), and adjust the position of looper thread take-up lever (I) so that
the side of looper thread take-up lever (I) comes over the center (L) of hole (J) as shown
in ** K **.

29

www.promelectroavtomat.ru

«
...
29
30
31
32
33
...
»

Содержание myLock 134D








































Отзывы:

Нет отзывов

Похожие инструкции для myLock 134D

Бренд: Adler Страницы: 20

Бренд: SYSFORM Страницы: 28

Бренд: Reliable Страницы: 1

Бренд: Reliable Страницы: 44

Бренд: Ricoh Страницы: 109

Бренд: Siruba Страницы: 28

Бренд: Pfaff Страницы: 78

Бренд: morse Страницы: 9

Бренд: Canon Страницы: 224

imagePRESS C7010VPS/C6010VPS/C6010S Series

Бренд: Canon Страницы: 100

Perfect Binder-C1

Бренд: Canon Страницы: 54

Perfect Binder-F1

Бренд: Canon Страницы: 74

Бренд: Canon Страницы: 128

Бренд: Canon Страницы: 140

Бренд: Canon Страницы: 2

Бренд: MBM Страницы: 47

Бренд: Magnum Страницы: 14

RoboCrib 2000 E

Бренд: AutoCrib Страницы: 53

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды