Janome myLock 134D Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 39

background image

CLEARANCE BETWEEN NEEDLE AND UPPER LOOPER

When the upper looper (A) meets with needle (B), the clearance (D) should be:

- 0.1 to +0.15mm (-1/256 to +3/512”) at the needle on the left.
- 0.2 to +0.05mm (-1/128 to +1/512”) at the needle on the right.

TO ADJUST
1. Turn the hand wheel toward you with your hand to bring the needle just behind the upper

looper (A) in downward travel.

2. Loosen the set screw (C), and adjust the clearance between the both needles and upper

looper (A).

3. Tighten the set screw (C).
4. Check the clearance between the loopers. (Refer to page 25.)
5. Check the upper looper position after the adjustment. (Refer to page 23.)

27

www.promelectroavtomat.ru

«
...
27
28
29
30
31
...
»

Содержание myLock 134D








































Отзывы:

Нет отзывов

Похожие инструкции для myLock 134D

MultiPASS L6000

Бренд: Canon Страницы: 39

Бренд: Canon Страницы: 103

Бренд: ADJ Страницы: 10

Бренд: Singer Страницы: 54

KM 150/500 R D 4W

Бренд: Kärcher Страницы: 420

Бренд: Duerkopp Adler Страницы: 25

martin yale CR828

Бренд: Southwest Страницы: 8

Бренд: Janome Страницы: 61

Truvox International Orbis Compact

Бренд: Tacony Страницы: 14

Бренд: Olivetti Страницы: 16

Бренд: Oki Страницы: 197

Бренд: Datasensor Страницы: 161

KM 70/30 C Bp Adv

Бренд: Kärcher Страницы: 147

Бренд: Minuteman Страницы: 20

APW-896N/IP-420

Бренд: JUKI Страницы: 142

AMS-221F3020RSW/AW-3

Бренд: JUKI Страницы: 163

Бренд: JUKI Страницы: 264

Бренд: Muratec Страницы: 106

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды