Janome MC6300P Скачать руководство пользователя страница 45

Страница: 45 / 50

[Correct condition]

(1) Bobbin winder switch

(SP)

Move the bobbin winder

lever to the right and left.

Right Left

Press the stitch length plus

button.

(2) Presser bar lifter switch

(FL)

Move the presser bar lifter

up and down.

Up Down

Press stitch length plus

button.

(3) Auto thread cutter switch

(cL)

Move the driving arm (1) up

and down.

Up [oF] Down [on]

Press the stitch length plus

button.

(4) Drop feed switch (dd)

Move the drop feed lever to

the right and left.

Left [UP] Right {dn]

Press the clear button to

proceed to the next step.

* By pressing the stitch

length minus button, you

can return to the previous

step.

3. Switch

Bobbin winder switch

Presser bar

lifter switch

Auto thread

cutter switch

Drop feed

switch

Bobbin winder

lever at right

Bobbin winder

lever at left

Presser bar

lifter “UP”

Presser bar

lifter “DOWN”

Auto thread

cutter clutch

“UP”

Auto thread

cutter clutch

“DOWN”

Drop feed lever

at left

Drop feed lever

at right

Cam groove

Pin (C)

Move the driving arm (1)

Auto thread

cutter switch

[Faulty condition]

The LED does not change, or

it shows conversely.

Adjust the position of the switch, or

replace the switch and/or circuit

board A.

Содержание MC6300P



















































Результаты поиска

Содержание MC6300P

Отзывы:

Похожие инструкции для MC6300P

Бренды по названию

Популярные бренды

Janome MC6300P, Руководство по обслуживанию

Результаты поиска

Содержание MC6300P

Отзывы:

Похожие инструкции для MC6300P

Бренды по названию

Популярные бренды