Janome MC6300P Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 50

background image

39

Yoke (A)

Plunger (B)

2.5 mm (C)

Setting plate (E)

Setscrews (D)

1. Remove the machine base (refer to page 2).

2. Loosen the 2 setscrews (D) and adjust the distance

to 2.5 mm (C) by moving the setting plate (E).

3. Tighten the 2 setscrews (D).

4. Attach the machine base.

TO ADJUST POSITION OF SOLENOID FOR AUTO THREAD CUTTER

The distance between the yoke (A) and the snap ring on the plunger (B) should be 2.5mm.

«
...
39
40
41
42
43
...
»

Содержание MC6300P



















































Отзывы:

Нет отзывов

Похожие инструкции для MC6300P

Бренд: Panasonic Страницы: 2

Бренд: Baby Lock Страницы: 12

Бренд: Baby Lock Страницы: 56

Бренд: Baby Lock Страницы: 20

Quilter's Choice Professional BLQP

Бренд: Baby Lock Страницы: 51

Quest PLUS BLQ2-PL

Бренд: Baby Lock Страницы: 2

Бренд: Baby Lock Страницы: 104

Бренд: Baby Lock Страницы: 2

Ellisimo Gold II

Бренд: Baby Lock Страницы: 96

Бренд: Baby Lock Страницы: 224

KX-TG2248S - 2.4 GHz Digital Cordless Phone Answering...

Бренд: Panasonic Страницы: 35

Бренд: Westomatic Страницы: 41

Бренд: HIGHLEAD Страницы: 35

Бренд: Singer Страницы: 20

EXPRESSION 2028

Бренд: Pfaff Страницы: 4

KH 4419 THERMAL BINDING MACHINE

Бренд: UNITED OFFICE Страницы: 14

Бренд: Briteq Страницы: 8

Бренд: Uniden Страницы: 95

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды