manualshive.com logo in svg

Janome MC6300P, Руководство по обслуживанию, Страница: 36 / 50

Поделиться
Скачать
Janome MC6300P Скачать руководство пользователя страница 36

34

TO ADJUST BUTTONHOLE LEVER POSITION

Buttonhole lever   Buttonhole foot (R)

Setscrew

(A)

Clearance (D)

1.4 mm- 1.8mm

Screw (E)

Buttonhole lever

guide (B)

Buttonhole

sensor signal

Buttonhole

sensor signal

(

Front)

(

Center)

(

Rear

)

Buttonhole lever (C)

1. While pressing the needle up/down and lock

stitch keys, turn the power switch on.

Press the stitch “34” within 3 seconds.

2. Remove the face plate (refer to page 1).

Lower the buttonhole lever (C).

3. Loosen the setscrew (A) and move the buttonhole

lever guide (B) until the LED shows “L”. Tighten

the setscrew (A).

4. Attach the buttonhole foot (R) and lower the

buttonhole lever.

5. Adjust the clearance of the buttonhole foot to 1.4

- 1.8mm (D).

6. Loosen the screw (E) until the LED shows “H”.

7. Tighten the screw (E) until the LED just changes

from “H” to “L”.

Place a sheet of paper under the buttonhole foot.

Then pull the paper toward you slowly until the

“Sensor” changes to “H”. In this condition, the

clearance (D) should be between 1.4mm and

1.8mm.

8. Turn off the power switch.

9. Attach the face plate.

Buttonhole

sensor signal

Содержание MC6300P



















































Отзывы:

Нет отзывов