background image

10

      CAUTION

Turn OFF the power switch before changing the 

needle.

Raise the needle to its highest position by turning the 

handwheel counterclockwise.

Insert the needle attached to the machine into the 

hole of the needle holder.

  q 

Needle holder

Loosen the needle clamp screw with the screwdriver 

(small) and remove the needle.

  w 

Small screwdriver

  e 

Needle clamp screw

Insert a new needle into the needle holder with the flat 

side to the rear.

  r 

Hole of needle holder

  t 

Flat side

Insert the needle into the needle clamp and push it up 

as far as it will go.

The top of the right needle should touches the bottom 

of the needle bar and the top of the left needle should 

touches the edge of the needle bar.

 

Left needle

  u 

Right needle

  i 

Edge of needle bar

  o 

Bottom of needle bar

Firmly tighten the needle clamp screw with the 

screwdriver (small) while holding the holder in place. 

Pull the needle holder down to remove the needle.

Checking the needle

To see if the needle is in good condition, place the flat 

side of the needle onto something flat (needle plate, glass 

etc.). The gap between the needle and the flat surface 

should be consistent. Never use a bent or blunt needle.

Flat side

Something flat

Gap

Changing the Needle

* Use an HA-1 SP #14 or #11 needle.

* An HA-1 SP #14 needle is set on the machine.

q

w

q

e

q

w

e

r

y

u

i

o

w

e

w

q

r

t

q

x c b m

n

Presser Foot Pressure Dial

Foot pressure can be adjusted by turning the presser foot 

pressure dial.

Set the pressure to “N” for ordinary fabrics.

Turn the dial toward you for light weight fabrics .

Turn the dial away from you for heavy weight fabrics.

  q

 Presser foot pressure dial

  w 

Setting mark

  e 

To increase

  r 

To decrease

You do not need to adjust the presser foot pressure for 

normal sewng.

After making an adjustment, sew and check the pressure.

v

NOTE:

Partially tighten the needle clamp screw on the side 

that is not being used to prevent losing the screw.

Содержание AT2000D


































































Отзывы: