Janome AT2000D Скачать руководство пользователя страница 11

Страница: 11 / 65

Handwheel

Match the “ ” mark of the belt cover with the “–” mark

of the handwheel when threading needles, adjusting

the chaining finger switch knob or raising/lowering the

spreader.
Always turn the handwheel toward you

(counterclockwise).

Handwheel

Belt cover

“ ” mark

“–” mark

Looper Cover

To open:

Hold the looper cover as illustrated and slide it to the right

as far as it will go.

Pull the looper cover toward you to open it.

Looper cover

To close:

Push the looper cover back up. The looper cover snaps

into position automatically.

Side Cover

To open:

Pull the side cover to the left.

Side cover

To close:

Push the side cover to the right.

NOTE:

Always close the looper cover when the machine is

in use. You cannot run the machine with the looper

cover open.

NOTE:

Always close the side cover when the machine is in

use. You cannot run the machine with the side cover

open.

Содержание AT2000D


































































Результаты поиска

Содержание AT2000D

Отзывы:

Похожие инструкции для AT2000D

Бренды по названию

Популярные бренды

Janome AT2000D, Инструкция

Результаты поиска

Содержание AT2000D

Отзывы:

Похожие инструкции для AT2000D

Бренды по названию

Популярные бренды