Janome AirThread 2000D страница 41 Скачать руководство пользователя

Страница: 41 / 45

Replacing External Parts

MODEL: AirThread 2000D

To replacing the motor (1)

Setscrew A

Motor pulley

Belt

Nut

Setscrew B

Machine socket

Machine socket cover

Motor (unit)

Motor terminals

Setscrew B

To remove:
1. Remove the belt cover, the rear cover and the

machine socket (unit).

2.  Remove the setscrews A (2 pcs.).
3.  Remove the motor.
4.  Remove the setscrews B (2 pcs.).
5.  Remove the machine socket cover.
6.  Remove the nuts.
7.  Remove the motor terminals from the machine socket.

To attach:
1.  Connect the motor terminals to the machine socket.
2.  Tighten the nuts.
3.  Attach the machine socket cover to the machine

socket.

4. Tighten the setscrews B (2 pcs).
5. Tighten the setscrews A (2 pcs.) to fix the motor on

the arm.

Содержание AirThread 2000D














































Результаты поиска

Содержание AirThread 2000D

Отзывы:

Похожие инструкции для AirThread 2000D

Бренды по названию

Популярные бренды

Janome AirThread 2000D, Руководство по обслуживанию

Результаты поиска

Содержание AirThread 2000D

Отзывы:

Похожие инструкции для AirThread 2000D

Бренды по названию

Популярные бренды