Janome AirThread 2000D Скачать руководство пользователя страница 44

Страница: 44 / 45

Replacing External Parts

MODEL: AirThread 2000D

To change the micro switch
(covers and looper threader switch lever)

To remove:
1. Remove the belt cover.
2. Remove the setscrew A and remove the switch set

plate 1.

3. Remove the setscrew B and remove the micro switch.
4. Remove the terminals from the relay cable RF (unit)

and the relay cable FF (unit).

To attach:
1. Insert the terminals into the relay cable RF (unit) and

the relay cable FF (unit).

2. Tighten the setscrew B to fix the micro switch to the

switch set plate 1.

3. Partially tighten the setscrew A to fix the switch set

plate 1 to the cover detecting base.

4. Close the side cover.
5. Adjust the position of the switch set plate 1 so that the

micro switch is set ON or OFF when the looper cover
is opened or closed.

6. Attach the belt cover.

Micro switch

Setscrew B

Setscrew A

Relay cable RF

Cover positipn detecting base

Relay cable FF

Switch set plate 1

Содержание AirThread 2000D














































Результаты поиска

Содержание AirThread 2000D

Отзывы:

Бренды по названию

Популярные бренды

Janome AirThread 2000D, Руководство по обслуживанию

Результаты поиска

Содержание AirThread 2000D

Отзывы:

Бренды по названию

Популярные бренды