Janome 1600P PROFESSIONAL - Скачать руководство пользователя | Manualshive

Страница: 18 / 29

background image

16

4. Circuit Board-A

To remove:

[1] Remove the top cover.

[2] Pull out connectors from the circuit board-A.

Remove the cords from the cord clips (1).

[3] Remove the setscrews (2) and the board-A

case lid (3).

[4] Pull out the connectors under the case lid.

Remove setscrews (4) and circuit board-A.

To attach:

[5] Install the circuit board-A and secure it with

the setscrews (4).

[6] Insert the following connectors:

(5) Machine socket (primary)
(6) Power transformer (primary)
(7) Driving motor

[7] Attach the board-A case lid (3) and secure it

with the setscrews (2).

Insert the remaining connectors and secure

the cords with the cord clips (1) on the case
lid.

Attach the top cover.

NOTE:

Do not disconnect the connectors by pulling on cord.
To disconnect, grasp the connector, not the cord.

5. Circuit Board-F and Slide Volume

[1] Remove the top cover.

[2] Loosen the 4 setscrews (1) and remove the

ornamental panel (2).

[3] Pull out the circuit board-F connector from the

circuit board-A. Remove the 3 setscrews (3)
and circuit board-F (4).

[4] Pull out the slide volume connector from the

circuit board-A. Remove the CS rings (5) and
slide volume (6).

[5] To attach: follow the above procedure in

reverse.

NOTE:

Do not disconnect the connectors by pulling on cord.
To disconnect, grasp the connector, not the cord.

(1)

(2)

(3)

(4)

(4)

(5)

(6)

(7)

(1)

(2)

(3)

(5)

(4)

(1)

(1)

(2)

(6)

«
...
16
17
18
19
20
...
»

Содержание 1600P PROFESSIONAL -






























Отзывы:

Нет отзывов

Похожие инструкции для 1600P PROFESSIONAL -

Бренд: Jack Страницы: 7

Бренд: Jack Страницы: 22

Бренд: IDEAL Страницы: 48

HQ Sweet Sixteen

Бренд: handi quilter Страницы: 30

Бренд: Neopost Страницы: 6

Бренд: Pfaff Страницы: 56

Бренд: Algam Lighting Страницы: 16

RootsScrub B6050

Бренд: ROOTS Страницы: 22

Бренд: Duerkopp Adler Страницы: 25

Citymaster 1250

Бренд: HAKO Страницы: 40

Бренд: Clarke Страницы: 28

Бренд: Oki Страницы: 653

Бренд: JUKI Страницы: 15

DDL-9000C Series

Бренд: JUKI Страницы: 198

Бренд: Koblenz Страницы: 4

Бренд: Singer Страницы: 4

Бренд: SSS Siedle Страницы: 17

Бренд: TurfTracker Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды