Janome 1600P PROFESSIONAL - Скачать руководство пользователя | Manualshive

Страница: 13 / 29

background image

11

14. Needle Stop Position

[1] Turn the power switch (1) on while pressing the Up/

Down needle position button (2) and bobbin winding

button (3) at the same time.

[2] Remove the top cover.

[3] Lower the needle bar by turning the hand wheel until

the needle point is 19.1 mm (for 1600P-DB/DBX) or

18.7 mm (for DP-1600P) above the upper surface of

the needle plate (4).

(Use the first step from the right for 19.1 mm or the

second step from the right for 18.7 mm).

[4] Loosen the setscrew (5). Rotate the upper shaft

shielding plate (6) toward you until the green LED (7)

turns on.

[5] Tighten the setscrew (5) and turn the power switch

off.

[6] Attach the top cover.

(1)

(2)

(3)

(5)

(4)

(6)

(7)

19.1 mm (1600P-DB/DBX)

18.7 mm (1600P)

19.1 mm

18.7 mm

«
...
11
12
13
14
15
...
»

Содержание 1600P PROFESSIONAL -






























Отзывы:

Нет отзывов

Похожие инструкции для 1600P PROFESSIONAL -

Бренд: Pfaff Страницы: 88

Бренд: weasy Страницы: 75

Бренд: Schwamborn Страницы: 50

Бренд: FONESTAR Страницы: 16

Бренд: JUKI Страницы: 40

Powr-Flite M1200-3

Бренд: Tacony Страницы: 8

Бренд: Datasensor Страницы: 161

Бренд: Singer Страницы: 40

Бренд: Muratec Страницы: 91

Бренд: Kärcher Страницы: 240

Бренд: Mi-T-M Страницы: 6

Бренд: Xblue Networks Страницы: 24

PhoneMate TA-150

Бренд: Casio Страницы: 38

Бренд: Singer Страницы: 41

Бренд: Rexel Страницы: 48

Бренд: Nilfisk-Advance Страницы: 40

Бренд: Scotsman Страницы: 78

Бренд: Deco Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды