J&M Speed Tender 535-ST Скачать руководство пользователя

Страница: 22 / 67

Specifications

2.0 Service

2.8 Adjusting Conveyor Belt Tracking

Loosen (Do Not Remove) the 4 bolts on the two bearing mounting plates located at the collapsible hopper end of the

conveyor (Figure 2.5).

NOTE: Only adjust conveyor in normal position, do not adjust in self-fill position.

Operate the conveyor at a slow speed.

CAUTION: Keep hands and clothing away from moving parts.

Loosen jam nut on adjustment bolt (Figure 2.5).

Tighten the adjustment bolt slowly until belt is running in the center of the pulley.

NOTE: Do not loosen the Adjustment bolt.

Tighten all bolts on bearing mounting plate, and adjustment bolts jam nuts.

Repeat at discharge end.

When belt is running in center of the pulley on both ends of conveyor, allow the Speed Tender to run for 10 min, and

recheck belt for proper tracking.

Conveyer

Clean-out Door

Figure 2.4

Remove

Loosen these

bolts when adjusting belt

tension. Typical each side.

Jam Nut

Adjustment Bolt

Bearing Mounting

Plate

Discharge Pan

Loosen these

bolts when adjusting belt

tension. Typical each side.

Jam Nut

Adjustment Bolt

Bearing Mounting

Plate

Figure 2.5

Jam Nut

Measurments A & B need to be the same.

Содержание Speed Tender 535-ST




































































Результаты поиска

Содержание Speed Tender 535-ST

Отзывы:

Похожие инструкции для Speed Tender 535-ST

Бренды по названию

Популярные бренды

J&M Speed Tender 535-ST, Руководство оператора

Результаты поиска

Содержание Speed Tender 535-ST

Отзывы:

Похожие инструкции для Speed Tender 535-ST

Бренды по названию

Популярные бренды