J&M Speed Tender 535-ST Скачать руководство пользователя

Страница: 40 / 67

5 - Function Manifold Valve Schematic (Aluminum) 2015 & Newer

3.2 Aluminum Valve Block

Con

yor

Up/D

t D

oor

Con

yor

Connector

Use good set of allen wrenches when changing orifices.

The cartridge should be tightened with 25 lbs. of torque.

The Coil nut should be tightened with 5 lbs. of torque.

There is a spring, poppit, and ball bearing at the bottom of each coil.

Top Coil operates bottom port.

Bottom Coil operates top port.

When changing cartridge make sure all functions are at rest.

The lettering on the coils should always be facing up.

Letter Function

Conveyor swing front (optional)

Conveyor swing rear (optional)

Conveyor Up

Conveyor Down

Rear door up (optional)

Front door down (optional)

Power

Front door up (optional)

Rear door down (optional)

Pump In

Conveyor Start

Содержание Speed Tender 535-ST




































































Результаты поиска

Содержание Speed Tender 535-ST

Отзывы:

Похожие инструкции для Speed Tender 535-ST

Бренды по названию

Популярные бренды

J&M Speed Tender 535-ST, Руководство оператора

Результаты поиска

Содержание Speed Tender 535-ST

Отзывы:

Похожие инструкции для Speed Tender 535-ST

Бренды по названию

Популярные бренды