J&M Speed Tender 535-ST Скачать руководство пользователя

Страница: 13 / 67

Specifications

1.0 Operations

Open door on Speed Tender using supplied remote. (Figure 1.4).

WARNING: Empty-out the rear compartment first to help prevent the chance of flipping the Speed Tender.

Use the Handheld Control or Wireless Remote to start the conveyor.

10.

Fill the planter/drill to desired level then repeat.

NOTE: Adjusting engine throttle will regulate conveyor speed.

11.

Close door on Speed Tender before the last planter seed box is full so you can completely empty-out collapsible hopper

and conveyor.

CAUTION: If you are parked on an incline the conveyor may swing freely. (It is advised that you do not use the

Speed Tender on uneven ground).

Figure 1.6

Figure 1.4

See Section 4.1 for Remote Options

Figure 1.5

Wireless

Remote

Handheld

Control

Hopper Up

Hydraulic

Door

Assembly

Содержание Speed Tender 535-ST




































































Результаты поиска

Содержание Speed Tender 535-ST

Отзывы:

Похожие инструкции для Speed Tender 535-ST

Бренды по названию

Популярные бренды

J&M Speed Tender 535-ST, Руководство оператора

Результаты поиска

Содержание Speed Tender 535-ST

Отзывы:

Похожие инструкции для Speed Tender 535-ST

Бренды по названию

Популярные бренды